JVC CS-SR100 Instructions - Page 2
Connection Diagram, Using the Speaker System, Parts Identification, Maintenance, Troubleshooting - sirius powered speaker set
UPC - 046838016318
View all JVC CS-SR100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
Connection Diagram REAR VIEW Home Docking Cradle for JVC Sirius tuner Audio Output (Green connector) Right Speaker REAR VIEW Left Speaker Green plug (stereo mini: φ 3.5 mm) Line input cord Using the Speaker System 1 Connect the speakers and AC adapter as shown in the Connection Diagram. 2 Turn the power switch knob clockwise to turn the power on. A click sound is heard and the power lamp lights up in green. 3 Turn the power switch knob further to obtain the optimum sound level. • In case the sound level is not sufficient though the knob is turned up fully clockwise, increase the output level of the signal source as it may be set too low. • When using the headphones, plug it into the headphone jack. No sound comes out of the speakers. Turn the knob fully counterclockwise before connecting the headphones, not to damage the speakers and your ears. To turn off the speakers, turn the power switch knob fully counterclockwise. • Never turn it on or off by any other means to ensure safe operation of the speakers. Black plug Brown connector Brown plug (mini: φ 2.5 mm) Left speaker cord AC adapter (AC 120 V , 60 Hz) To an AC outlet After completing all other connections, plug in the AC adapter. Maintenance If cleaning is required, disconnect the AC adapter from AC outlet, and wipe off with soft cloth. For removing heavy stain, use the cloth moistened with neutral detergent. Do not use inflammable or harmful fluid such as benzine or thinner. Parts Identification 7 Front Left speaker Right speaker 7 Rear Power lamp Headphone jack Power switch (volume control) knob Right speaker Left speaker Line-input cord (green plug): 2 m (6.5 ft) DC IN jack L SPKR (left speaker) jack (brown connector) Left speaker cord (brown plug): 2 m (6.5 ft) Troubleshooting Check the following if you think the system is not working correctly. • If the problem should persist, unplug the AC adapter from the AC outlet, and refer servicing to the qualified service personnel. Symptom Possible Cause Remedy Power lamp is turned off. • AC adapter is not connected. • No power is supplied. • Plug in adapter firmly. • Try another AC outlet. Power lamp is turned • Line-input cord is not connected. on, but no sound. • Volume level is too low. • Plug in the cord firmly. • Turn up the volume control. Sound is distorted. • Volume level is too high. • Input sound level is too high. • Turn down the volume control. • Adjust it to the optimum level. Sound level is too low. • Input sound level is too low. • Adjust it to the optimum level. Sound comes out of only one speaker. • Line-input cord is not connected firmly. • Plug in the cord firmly. • Left speaker is not connected to the right speaker. • Plug in Speaker cord firmly. Although the speakers are magnetically shielded, they may affect some monitors if installed nearby. Should color deterioration occur on a monitor, place the speakers slightly away. Turn off the monitor, and keep it turned off for about 15 to 20 minutes. By doing this, normal color will be restored. Specifications 7 Amplifier: Power output Input impedance Input sensitivity Power supply Power consumption Signal-to-noise ratio 1.5 W per channel (at 10 % THD) 12 kΩ (nominal) 200 mV/1 kHz/1 W DC 9 V 500 mA (by AC adapter) 12 W 72 dB 7 Power Requirements: AC 120 V , 60 Hz 7 Speaker System: Enclosures Frequency response Speaker uint Plastic molded 100 Hz - 20 000Hz 90 mm x 50 mm (3-9/16 in. x 2 in.) cone type, magnetically shielded 7 Dimensions (H/W/D): Right speaker: 200 mm x 80.5 mm x 112 mm (7-7/8 in. x 3-1/4 in. x 4-7/16 in.) Left speaker: 200 mm x 80.5 mm x 99.3 mm (7-7/8 in. x 3-1/4 in. x 3-15/16 in.) 7 Mass: Right speaker: 400 g (0.89 lbs) Left speaker: 345 g (0.77 lbs) * Design and specifications are subject to change without notice.