JVC DVM96U User Manual - Page 86

high-precision technology.

Get JVC DVM96U - Camcorder - 1.0 Megapixel PDF manuals and user guides
UPC - 046838160837
View all JVC DVM96U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

86 EN TROUBLESHOOTING (cont.) 31. When the image is printed from the printer, a black bar appears at the bottom of the screen. 31. • This is not a malfunction. 31. • By recording with "DIS" activated (੬ pg. 46) this can be avoided. 32. When the camcorder is 32. • The DV cable was plugged/ connected via the DV unplugged with power connector, the camcorder does turned on. not operate. 32. • Turn the camcorder's power off and on again, then operate it. 33. The rear of the LCD monitor is 33. • The light used to illuminate 33. • Close the LCD monitor to hot. the LCD monitor causes it to turn it off or set the Power become hot. Switch to "OFF", and let the unit cool down. 34. Images on the LCD monitor appear dark or whitish. 34. • In places subject to low 34. • Adjust the brightness and temperature, images become angle of the LCD monitor. dark due to the (੬ pg. 13) characteristics of the LCD monitor. When this happens, the displayed colours differ from those that are actually recorded. This is not a defect of the camcorder. • When the LCD monitor's fluorescent light reaches the end of its service life, images on the LCD monitor become dark. Consult your nearest JVC dealer. 35. Coloured bright spots appear 35. • The LCD monitor and the 35. all over the LCD monitor or the viewfinder are made with viewfinder. high-precision technology. However, black spots or bright spots of light (red, green or blue) may appear constantly on the LCD - monitor or the viewfinder. These spots are not recorded on the tape. This is not due to any defect of the unit. (Effective dots: more than 99.99 %) 36. The indicators and the image 36. • This may occur when the 36. colour on the LCD monitor are surface or the edge of the - not clear. LCD monitor is pressed. 37. The cassette will not load properly. 37. • The cassette is in the wrong position. • The battery's charge is low. 37. • Set it in the right position. (੬ pg. 16) • Install a fully charged battery. (੬ pg. 10, 11) 38. The memory card will not load 38. • The memory card is in the 38. • Set it in the right position. properly. wrong position. (੬ pg. 17) 39. The memory card cannot be 39. removed from the camcorder. - 39. • Push in the memory card a few more times. (੬ pg. 17)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
86
EN
31.
When the image is printed
from the printer, a black bar
appears at the bottom of the
screen.
31.
•This is not a malfunction.
31.
•By recording with “DIS”
activated (
±
pg. 46) this can
be avoided.
32.
When the camcorder is
connected via the DV
connector, the camcorder does
not operate.
32.
•The DV cable was plugged/
unplugged with power
turned on.
32.
•Turn the camcorder’s power
off and on again, then
operate it.
33.
The rear of the LCD monitor is
hot.
33.
•The light used to illuminate
the LCD monitor causes it to
become hot.
33.
•Close the LCD monitor to
turn it off or set the Power
Switch to “OFF”, and let the
unit cool down.
34.
Images on the LCD monitor
appear dark or whitish.
34.
•In places subject to low
temperature, images become
dark due to the
characteristics of the LCD
monitor. When this happens,
the displayed colours differ
from those that are actually
recorded. This is not a defect
of the camcorder.
•When the LCD monitor’s
fluorescent light reaches the
end of its service life, images
on the LCD monitor become
dark. Consult your nearest
JVC dealer.
34.
•Adjust the brightness and
angle of the LCD monitor.
(
±
pg. 13)
35.
Coloured bright spots appear
all over the LCD monitor or the
viewfinder.
35.
•The LCD monitor and the
viewfinder are made with
high-precision technology.
However, black spots or
bright spots of light (red,
green or blue) may appear
constantly on the LCD
monitor or the viewfinder.
These spots are not recorded
on the tape. This is not due to
any defect of the unit.
(Effective dots: more than
99.99 %)
35.
—
36.
The indicators and the image
colour on the LCD monitor are
not clear.
36.
•This may occur when the
surface or the edge of the
LCD monitor is pressed.
36.
—
37.
The cassette will not load
properly.
37.
•The cassette is in the wrong
position.
•The battery’s charge is low.
37.
•Set it in the right position.
(
±
pg. 16)
•Install a fully charged battery.
(
±
pg. 10, 11)
38.
The memory card will not load
properly.
38.
•The memory card is in the
wrong position.
38.
•Set it in the right position.
(
±
pg. 17)
39.
The memory card cannot be
removed from the camcorder.
39.
—
39.
•Push in the memory card a
few more times. (
±
pg. 17)
TROUBLESHOOTING (cont.)