JVC KD R200 Instructions - Page 3

INSTRUCTIONS General settings-PSM Enter PSM menu. Select an item. Adjust. Finish Indication DEMO CLK DISP*1 CLOCK H (Hour) CLOCK M (Minute) DIMMER SCROLL *2 L/O MODE WOOFER *3 AUX ADJ TAG DISP AMP GAIN*4 AREA Item ( : Initial) Setting • DEMO ON • DEMO OFF : Display demonstration will be activated automatically if no operation is done for about 20 seconds. : Cancels. • ON • OFF : Clock time is shown on the display at all times when the power is turned off. : Cancels; pressing DISP will show the clock time for about 5 seconds when the power is turned off. 1 - 12 : [Initial: 1 (1:00)] 00 - 59 : [Initial: 00 (1:00)] • ON • OFF : Dims the display and button illumination. : Cancels. • ONCE • AUTO • OFF : Scrolls the displayed information once. : Repeats scrolling (at 5-second intervals). : Cancels. • Pressing DISP for more than one second can scroll the display regardless of the setting. • REAR • WOOFER : Select if the REAR LINE OUT terminals are used for connecting the speakers (through an external amplifier). : Select if the REAR LINE OUT terminals are used for connecting a subwoofer. • LOW • MID • HIGH : Frequencies lower than 90 Hz are sent to the subwoofer. : Frequencies lower than 135 Hz are sent to the subwoofer. : Frequencies lower than 180 Hz are sent to the subwoofer. A.ADJ 00 - A.ADJ 05 : Adjust the auxiliary input level to avoid the sudden increase of the output level when changing the source from external component connected to the AUX input jack on the control panel. • TAG ON • TAG OFF : Shows the Tag while playing MP3/WMA tracks. : Cancels. • LOW PWR • HIGH PWR : VOL 00 - VOL 30 (Select if the maximum power of each speaker is less than 50 W to prevent damaging the speaker.) : VOL 00 - VOL 50 • AREA US • AREA EU • AREA SA : When using in North/Central/South America. AM/FM intervals are set to 10 kHz/200 kHz. : When using in any other areas. AM/FM intervals are set to 9 kHz/50 kHz (100 kHz during auto search). : When using in South American countries where FM interval is 100khz. AM interval is set to 10khz. *1 If the power supply is not interrupted by turning off the ignition key of your car, it is recommended that you select "OFF" to save the car's battery. *2 Some characters or symbols will not be shown correctly (or will be blanked) on the display. *3 Displayed only when "L/O MODE" is set to "WOOFER." *4 The volume level automatically changes to "VOL 30" if you change to "LOW PWR" while the volume level is set higher than "VOL 30." SPECIFICATIONS Audio amplifier section Power Output: 20 W RMS × 4 Channels at 4 Ω and ≤ 1% THD+N Signal-to-Noise Ratio: 80 dBA (reference: 1 W into 4 Ω) Load Impedance: 4 Ω (4 Ω to 8 Ω allowance) Tone Control Range: Bass: ±12 dB at 60 Hz Mid-range: ±12 dB at 1 kHz Treble: ±12 dB at 7.5 kHz Frequency Response: 40 Hz to 20 000 Hz Line-Out Level/Impedance: 2.5 V/20 kΩ load (full scale) Output Impedance: 1 kΩ Subwoofer-Out Level/Impedance: 2.5 V/20 kΩ load (full scale) If a kit is necessary for your car, consult your telephone directory for the nearest car audio speciality shop. Tuner section Frequency Range: FM: 87.5 MHz to 107.9 MHz (with channel interval set to 100 kHz or 200 kHz) 87.5 MHz to 108.0 MHz (with channel interval set to 50 kHz) AM: 530 kHz to 1 710 kHz (with channel interval set to 10 kHz) 531 kHz to 1 602 kHz (with channel interval set to 9 kHz) [FM Tuner] Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω) 50 dB Quieting Sensitivity: 16.3 dBf (1.8 μV/75 Ω) Alternate Channel Selectivity (400 kHz): 65 dB Frequency Response: 40 Hz to 15 000 Hz Stereo Separation: 35 dB [AM Tuner] Sensitivity/Selectivity: 20 μV/35 dB TROUBLESHOOTING Symptoms Remedies/Causes • Sound cannot be heard from the speakers. • Adjust the volume to the optimum level. • Check the cords and connections. General • The buttons on the unit do not work as you If you press M MODE, some buttons work differently from it intended. original function. Wait for 5 seconds or press M MODE again. • This unit does not work at all. Reset the unit. FM/AM • SSM automatic presetting does not work. Store stations manually. • Static noise while listening to the radio. Connect the antenna firmly. • Disc ejects. Insert the disc correctly. • CD-R/CD-RW cannot be played back. • Tracks on the CD-R/CD-RW cannot be skipped. • Insert a finalized CD-R/CD-RW. • Finalize the CD-R/CD-RW with the component which you used for recording. Disc playback • Disc can be neither played back nor ejected. • Unlock the disc. • Eject the disc forcibly. • Disc sound is sometimes interrupted. • Stop playback while driving on rough roads. • Change the disc. • Check the cords and connections. • "NO DISC" appears on the display. • "PLEASE" and "EJECT" appear alternately on the display. Insert a playable disc into the loading slot. • Disc cannot be played back. • Use a disc with MP3/WMA tracks recorded in a format compliant with ISO 9660 Level 1, Level 2, Romeo, or Joliet. • Add the extension code or to the file names. • Noise is generated. Skip to another track or change the disc. (Do not add the extension code or to non-MP3 or WMA tracks.) MP3/WMA playback • A longer readout time is required Do not use too many hierarchical levels and folders. ("READING" keeps flashing on the display). • Tracks are not played back in the order you Playback order is determined when the files are recorded. have intended. • The elapsed playing time is not correct. This sometimes occurs during playback. This is caused by how the tracks are recorded on the disc. • The correct characters are not displayed This unit can only display alphabets (upper case), numbers, and a (e.g. album name). limited number of symbols. • Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. CD player section Type: Compact disc player Signal Detection System: Non-contact optical pickup (semiconductor laser) Number of channels: 2 channels (stereo) Frequency Response: 5 Hz to 20 000 Hz Dynamic Range: 93 dB Signal-to-Noise Ratio: 98 dB Wow and Flutter: Less than measurable limit MP3 Decoding Format: MPEG1/2 Audio Layer 3 Max. Bit Rate: 320 kbps WMA (Windows Media® Audio) Decoding Format : Max. Bit Rate: 192 kbps Having TROUBLE with operation? Please reset your unit Still having trouble?? Call 1-800-252-5722 (USA ONLY) http://www.jvc.com General Power Requirement: Operating Voltage: DC 14.4 V (11 V to 16 V allowance) Grounding System: Negative ground Allowable Operating Temperature: 0°C to +40°C (32°F to 104°F) Dimensions (W × H × D): Installation Size (approx.): 182 mm × 52 mm × 160 mm (7-3/16" × 2-1/16" × 6-5/16") Panel Size (approx.): 188 mm × 58 mm × 5 mm (7-7/16" × 2-5/16" × 1/4") Mass (approx.): 1.3 kg (2.9 lbs) (excluding accessories) Design and specifications are subject to change without notice. PREPARATION WARNINGS TROUBLESHOOTING This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers. Prepare this before installation To prevent short circuits, we recommend that you disconnect the battery's negative terminal and make all electrical connections before installing the unit. • Be sure to ground this unit to the car's chassis again after installation. Notes: • Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer. • It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, change "AMP GAIN" setting to prevent the speakers from being damaged (see "General settings-PSM"). • To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape. • The heat sink becomes very hot after use. Be careful not to touch it when removing this unit. Heat sink • The fuse blows. * Are the red and black leads connected correctly? • Power cannot be turned on. * Is the yellow lead connected? • No sound from the speakers. * Is the speaker output lead short-circuited? • Sound is distorted. * Is the speaker output lead grounded? * Are the "-" terminals of L and R speakers grounded in common? • Noise interfere with sounds. * Is the rear ground terminal connected to the car's chassis using shorter and thicker cords? • This unit becomes hot. * Is the speaker output lead grounded? * Are the "-" terminals of L and R speakers grounded in common? • This unit does not work at all. * Have you reset your unit? 3 - EN