JVC KD-R490 Instruction Manual America - Page 23

Installing the unit in-dash mounting, Part list for installation, Basic procedure, How to remove

Get JVC KD-R490 PDF manuals and user guides View all JVC KD-R490 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

INSTALLATION/CONNECTION Part list for installation (A) Faceplate (B) Trim plate Installing the unit (in-dash mounting) Do the required wiring. ( 24) (C) Mounting sleeve (D) Wiring harness (E) Extraction key Basic procedure 1 Remove the key from the ignition switch, then disconnect the terminal of the car battery. 2 Connect the wires properly. See Wiring connection. ( 24) 3 Install the unit to your car. See Installing the unit (in-dash mounting). 4 Connect the terminal of the car battery. 5 Detach the faceplate and reset the unit. ( 3) Hook on the top side Orientate the trim plate as illustrated before fitting. Dashboard of your car Bend the appropriate tabs to hold the sleeve firmly in place. When installing without the mounting sleeve 1 Remove the mounting sleeve and trim plate from the unit. 2 Align the holes in the unit (on both sides) with the vehicle mounting bracket and secure the unit with screws (commercially available). How to remove the unit Use only the specified screws. Using wrong screws might damage the unit. ENGLISH 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
ENGLISH
23
INSTALLATION/CONNECTION
Installing the unit (in-dash mounting)
Part list for installation
Basic procedure
1
Remove the key from the ignition switch, then disconnect
the
terminal of the car battery.
2
Connect the wires properly.
See Wiring connection.
(
24)
3
Install the unit to your car.
See Installing the unit (in-dash mounting).
4
Connect the
terminal of the car battery.
5
Detach the faceplate and reset the unit.
(
3)
How to remove the unit
When installing without the mounting sleeve
1
Remove the mounting sleeve and trim plate from the unit.
2
Align the holes in the unit (on both sides) with the
vehicle mounting bracket and secure the unit with screws
(commercially available).
Use only the specified screws. Using wrong screws might
damage the unit.
Do the required wiring.
(
 
24)
Bend the appropriate tabs to hold
the sleeve firmly in place.
Hook on the top side
Orientate the trim
plate as illustrated
before fitting.
Dashboard of
your car
(A)
Faceplate
(B)
Trim plate
(D)
Wiring harness
(C)
Mounting sleeve
(E)
Extraction key