JVC KS-AX3102 Instructions - Page 2

SPEAKER CONNECTIONS Connection varies depending on the number of the speakers used in your car. Select the appropriate connection referring to the following diagrams. Notes • Securely connect all the parts. If the connections are loose, due to contact resistance etc., heat will break out and may cause an accident. • Run the connection leads under the car mats to prevent accidental disconnections. Å When your receiver is equipped with line output. ı When your receiver is NOT equipped with line output. KS-AX3104 KS-AX3102 KS-AX3101D FRONT REAR • Connect each lead of the speaker input connector to a speaker positive lead or chassis*1 of the receiver. • Cover the terminals of unused speaker negative leads of the receiver with insulating tape to prevent short circuits. *1 Example: connecting to the ground Black lead of the speaker input connector Rear ground terminal *2 Not supplied RECEIVER GND KS-AX3104 4-speaker system-Normal Mode • Use the speakers with an impedance of 2 Ω to 8 Ω. Å JVC car receiver, etc. Front JVC car receiver, etc. FRONT Front REAR KS-AX3102 2-speaker system-Normal Mode • Use the speakers with an impedance of 2 Ω to 8 Ω. Å JVC car receiver, etc. ı Speaker input connector. Line out Connector lead a White "LEFT (+)" To Receiver = Left (+) lead b Black "RECEIVER GND" = Chassis*1 *2 c Gray "RIGHT (+)" = Right (+) lead INPUT HIGH INPUT L/MONO LEVEL MIN MAX R CROSSOVER LPF OFF HPF 2-speaker system plus subwoofer • Use the speakers with an impedance of 2 Ω to 8 Ω. Line out (Rear) or Å JVC car receiver, etc. Subwoofer out *2 JVC amplifier, etc. (Purchased separately) Line out (Front) *2 ı Speaker input connector. Connector lead To Receiver a White "LEFT (+)" = Left (+) lead b Black "RECEIVER GND" = Chassis*1 c Gray "RIGHT (+)" = Right (+) lead Subwoofer INPUT HIGH INPUT L/MONO LEVEL MIN MAX R CROSSOVER LPF OFF HPF Line out (Front) Rear Rear Line out *2 *2 (Rear) CROSSOVER LPF OFF HPF INPUT HIGH INPUT HIGH INPUT LEVEL L/MONO L/MONO LEVEL CROSSOVER LPF OFF HPF MIN MAX R MIN MAX R FRONT REAR ı Speaker input connector. Connector lead To Receiver a White "FRONT LEFT (+)" = Front left (+) lead b Black "RECEIVER GND" = Chassis*1 c Gray "FRONT RIGHT (+)" = Front right (+) lead Connector lead To Receiver d Green "REAR LEFT (+)" = Rear left (+) lead e Black "RECEIVER GND" = Chassis*1 f Purple "REAR RIGHT (+)" = Rear right (+) lead 2-speaker system plus subwoofer-Bridge Mode • Use the speakers with an impedance of 2 Ω to 8 Ω. • Use the subwoofer with an impedance of 4 Ω to 8 Ω. Å Front FRONT REAR JVC car receiver, etc. Front Line out (Front) *2 Line out (Rear) or *2 Subwoofer out CROSSOVER LPF OFF HPF INPUT HIGH INPUT HIGH INPUT LEVEL L/MONO L/MONO LEVEL CROSSOVER LPF OFF HPF MIN MAX R MIN MAX R Subwoofer FRONT REAR ı Speaker input connector. Connector lead To Receiver a White "FRONT LEFT (+)" = Front left (+) lead b Black "RECEIVER GND" = Chassis*1 c Gray "FRONT RIGHT (+)" = Front right (+) lead Connector lead To Receiver d Green "REAR LEFT (+)" = Rear left (+) lead e Black "RECEIVER GND" = Chassis*1 f Purple "REAR RIGHT (+)" = Rear right (+) lead 2-speaker system-Bridge Mode • Use the speakers with an impedance of 4 Ω to 8 Ω. • Be sure to connect the line output from the receiver to the left (L) jack on this unit. Å FRONT REAR JVC car receiver, etc. Front Front Line out *2 CROSSOVER LPF OFF HPF INPUT HIGH INPUT HIGH INPUT LEVEL L/MONO L/MONO LEVEL CROSSOVER LPF OFF HPF MIN MAX R MIN MAX R FRONT REAR ı Speaker input connector. Connector lead To Receiver a White "FRONT LEFT (+)" = Front left (+) lead b Black "RECEIVER GND" = Chassis*1 c Gray "FRONT RIGHT (+)" = Front left (+) lead Connector lead To Receiver d Green "REAR LEFT (+)" = Front right (+) lead e Black "RECEIVER GND" = Chassis*1 f Purple "REAR RIGHT (+)" = Front right (+) lead Subwoofer system-Bridge Mode • Use the speakers with an impedance of 4 Ω to 8 Ω. Å JVC car receiver, etc. Line out (Rear) or Subwoofer out *2 ı Speaker input connector. Connector lead To Receiver a White "LEFT (+)" = Left (+) lead b Black "RECEIVER GND" = Chassis*1 c Gray "RIGHT (+)" = Right (+) lead INPUT HIGH INPUT L/MONO LEVEL MIN MAX R CROSSOVER LPF OFF HPF Subwoofer 2-speaker system (2 amplifiers)-Bridge Mode • Use the speakers with an impedance of 4 Ω to 8 Ω. • Be sure to connect the line output from the receiver to the left (L) jack on this unit. Å JVC car receiver, etc. ı Speaker input connector. Line out Connector lead a White "LEFT (+)" To Receiver = Front right (+) lead b Black "RECEIVER GND" = Chassis*1 *2 c Gray "RIGHT (+)" = Front right (+) lead INPUT HIGH INPUT L/MONO LEVEL MIN MAX R CROSSOVER LPF OFF HPF INPUT HIGH INPUT L/MONO LEVEL CROSSOVER LPF OFF HPF MIN MAX R ı Speaker input connector. Connector lead To Receiver a White "LEFT (+)" = Front left (+) lead b Black "RECEIVER GND" = Chassis*1 c Gray "RIGHT (+)" = Front left (+) lead KS-AX3101D Subwoofer system • Use the speakers with an impedance of 2 Ω to 8 Ω. Å JVC car receiver, etc. Line out (Rear) or Subwoofer out *2 ı Speaker input connector. Connector lead To Receiver a White "LEFT (+)" = Left (+) lead b Black "RECEIVER GND" = Chassis*1 c Gray "RIGHT (+)" = Right (+) lead PRE OUT INPUT HIGH INPUT L L/MONO R R Subwoofer 2