JVC XV-N310B Instructions - Page 7
Connecting to a TV with component jacks, Progressive scan video playback available - dvd player
![]() |
UPC - 046838012624
View all JVC XV-N310B manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
C Connecting to a TV with component jacks You can enjoy picture of high-fidelity color reproduction by connecting the COMPONENT VIDEO OUT jacks on the player to your TV. NOTES • Connect "Y" to "Y," "PB" to "PB" (CB), "PR" to "PR" (CR) correctly. • When using the COMPONENT VIDEO OUT jacks, do not connect the S-VIDEO output jack on the player. • If your TV has component video input jacks of BNC type, use an adapter which converts a pin jack to a BNC jack (not supplied). Progressive scan video playback available In the Progressive scanning mode, you can enjoy high quality picture with less flickers when the COMPONENT VIDEO OUT jacks are connected to a TV or monitor that supports the progressive video input. About the scanning mode Depending on the material source format, DVD VIDEO discs can be classified into two types; film source and video source (note that some DVD VIDEO discs contain both film source and video source). Film sources are recorded as 24-frame-persecond information, while (NTSC) video sources are recorded as 30-frame-per-second (60-field-per-second interlaced) information. When the player plays back a film source material, uninterlaced progressive output signals are created using the original information. When a video source material is played back, the player interleaves lines between the interlaced lines on each to create the interpolated picture and outputs as the progressive signal. Preparations The player Component video cable (not supplied) REMOTE 480p 480i VIDEO SIGNAL SELECTOR Blue Green Red Y PB PR COMPONENT VIDEO White TV IN S-VIDEO VIDEO LEFT AUDIO RIGHT 480p 480i REMOTE VISDEELOESCITGONRAL COMPAUV LINK Green Red VIDEO Y COMPONENT S-VIDEO PB PR VIDEO OUT LEFT PDCIGMI/TSATLROEUATM RIGHT AUDIO OUT COAXIAL Red Blue Audio cable (not supplied) White Red Selecting the VIDEO SIGNAL SELECTOR position • If your television equipped with component jacks does not support the progressive scanning mode Set the VIDEO SIGNAL SELECTOR to "480i." • If your television equipped with component jacks supports the progressive scanning mode Set the VIDEO SIGNAL SELECTOR to "480p." • If you want to select the scanning mode between the interlace and progressive modes (depending on the source condition, or when connecting more than one television, etc.) Set the VIDEO SIGNAL SELECTOR to "REMOTE." Thus you can select the mode from the remote control unit. Activating the Progressive scanning mode using the remote control unit When the player is turned on and the VIDEO SIGNAL SELECTOR is set to "REMOTE," press and hold down VFP PROGRESSIVE SCAN for a few seconds. The scanning mode switches between the Progressive scanning and Interlaced scanning modes. When the scanning mode is set to the Progressive mode, the [P] indicator lights up in the display window. Depending on the [PICTURE SOURCE] preference display and whether the current DVD VIDEO disc is film-source or videosource, the indicator that lights up in the display window differs, as shown in the table below. Setting of [PICTURE SOURCE] Source type of DVD VIDEO Film source Video source AUTO [DDP] [P] FILM [DDP] [DDP] VIDEO (NORMAL)/ [P] [P] (ACTIVE) NOTES • The Progressive scanning mode works only when you connect the player's COMPONENT VIDEO OUT jacks to your TV. • There are some progressive TV and High-Definition TV sets that are not fully compatible with the player, resulting in the unnatural picture when playing back a DVD VIDEO disc in the Progressive scanning mode. In such a case, use the Interlaced scanning mode. To check the compatibility of your TV set, contact your local JVC customer service center. • All JVC progressive TV and High-Definition TV sets are fully compatible with the player (Example: AV-61S902). • The VIDEO jack, S-VIDEO jack and COMPONENT VIDEO OUT jacks cannot be used at the same time. Connect cable(s) only to the jack(s) you want to use. 5
![](/manual_guide/products/jvc-xvn310b-instructions-02f7f4b/7.png)