JVC XV-N312S Instructions - Page 11

Starting playback, To stop playback temporarily

Page 11 highlights

Basic playback 5 Press ENTER. The third page is shown, in which the pull-down menu of the [DIGITAL AUDIO OUTPUT] is already open. DVD PLAYER SET UP DIGITAL AUDIO OUTPUT ANALOG DOWN MIX D RANGE CONTROL OUTPUT LEVEL DOLBY DIGITAL/PCM PCM ONLY DDOOLLBBYYPDRIOGLIOTGAILC/PCM SOTNREAM/PCM SELECT ENTER USE 5∞23 TO SELECT, USE ENTER TO CONFIRM TO EXIT, PRESS SETUP. DIGITAL AUDIO OUTPUT options 6 Press 5/∞ to select a desired digital output signal type. Set this item correctly when you connect the player to an external surround decoder or D/A converter. (If you do not connect the player to such a device, you do not have to set this item.) • When connecting to other digital device, select [PCM ONLY]. • When connecting to a Dolby Digital decoder, select [DOLBY DIGITAL/PCM]. • When connecting to a DTS decoder, select [STREAM/ PCM]. 7 Press ENTER. The TV screen returns to the opening display. To bring up the DVD PLAYER SET UP display later Press SET UP for a few seconds until the DVD PLAYER SET UP display appears. Starting playback 1 Press 0 (or OPEN/CLOSE on the remote control unit) to open the disc tray. 2 Place a disc in the disc tray. With the label side up If a menu is shown on the TV screen When inserting a DVD VIDEO, SVCD or Video CD disc, a menu may be shown on the TV screen. From the menu, you can select a desired item to be played back. For DVD VIDEO 1 Press 5/∞/2/3 to select a desired item. 2 Press ENTER or 3 (SELECT). The player starts playback of the selected item. For SVCD/Video CD Press the numeric buttons to select a desired item. The player starts playback of the selected item. NOTES • Do not insert an unplayable disc. (See page 2.) • When inserting a disc on the disc tray, be sure to position the disc inside the recess. Otherwise, the disc may be damaged when the disc tray is closed, or you may not be able to remove the disc from the player. To check the playback status You can see the current selection number (the title/chapter number for DVD VIDEO or track number for SVCD/Video CD/ Audio CD), time information (the track or chapter time while stopped, or elapsed track or chapter time during playback) and the transport status (stop, playback, pause, etc.) on the TV screen. Press ON SCREEN. Example: for DVD VIDEO Transfer rate Current chapter Current transport number status 8.5Mbps TITLE 33 CHAP 33 TOTAL 1:25:58 Current title number Disc elapsed time Note that pressing ON SCREEN again brings up the menu bar under the status bar, from which you can access various functions. See page 18 for details about the menu bar. To turn off the status bar Press ON SCREEN repeatedly until the status bar goes off. To change the display window contents Press DISPLAY. Example: for DVD VIDEO Each time you press DISPLAY, the total time display and the title/chapter number display appear alternately. • To insert an 8-cm disc, place it in the inner recess. 3 Press 0 (or OPEN/CLOSE on the remote control unit) to close the disc tray. 4 Press 3 on the unit or 3 (SELECT) on the remote control unit. The player starts playback from the beginning. • Depending on the disc, playback starts when you close the disc tray. Total time Title number Chapter number To stop playback completely Press 7. Hint If you press 0 during playback, the player stops playback and opens the disc tray. To stop playback temporarily Press 8. To resume playback, press 3 (SELECT). (See the following item.) 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39

9
B
a
s
i
c
p
l
a
y
b
a
c
k
5
Press ENTER.
The third page is shown, in which the pull-down menu of the
[DIGITAL AUDIO OUTPUT] is already open.
6
Press
5
/
to select a desired digital output
signal type.
Set this item correctly when you connect the player to an
external surround decoder or D/A converter. (If you do not
connect the player to such a device, you do not have to set
this item.)
• When connecting to other digital device, select [PCM
ONLY].
• When connecting to a Dolby Digital decoder, select
[DOLBY DIGITAL/PCM].
• When connecting to a DTS decoder, select [STREAM/
PCM].
7
Press ENTER.
The TV screen returns to the opening display.
To bring up the DVD PLAYER SET UP display later
Press SET UP for a few seconds until the DVD PLAYER SET UP
display appears.
Starting playback
1
Press
0
(or OPEN/CLOSE on the remote
control unit) to open the disc tray.
2
Place a disc in the disc tray.
3
Press
0
(or OPEN/CLOSE on the remote
control unit) to close the disc tray.
4
Press
3
on the unit or
3
(SELECT) on the
remote control unit.
The player starts playback from the beginning.
• Depending on the disc, playback starts when you close the
disc tray.
If a menu is shown on the TV screen
When inserting a DVD VIDEO, SVCD or Video CD disc, a menu
may be shown on the TV screen. From the menu, you can select
a desired item to be played back.
For DVD VIDEO
1 Press
5
/
/
2
/
3
to select a desired item.
2
Press ENTER or
3
(SELECT).
The player starts playback of the selected item.
For SVCD/Video CD
Press the numeric buttons to select a desired item.
The player starts playback of the selected item.
NOTES
• Do not insert an unplayable disc. (See page 2.)
• When inserting a disc on the disc tray, be sure to position the
disc inside the recess. Otherwise, the disc may be damaged
when the disc tray is closed, or you may not be able to remove
the disc from the player.
To check the playback status
You can see the current selection number (the title/chapter
number for DVD VIDEO or track number for SVCD/Video CD/
Audio CD), time information (the track or chapter time while
stopped, or elapsed track or chapter time during playback) and
the transport status (stop, playback, pause, etc.) on the TV
screen.
Press ON SCREEN.
Example: for DVD VIDEO
Note that pressing ON SCREEN again brings up the menu bar
under the status bar, from which you can access various
functions. See page 18 for details about the menu bar.
To turn off the status bar
Press ON SCREEN repeatedly until the status bar goes off.
To change the display window contents
Press DISPLAY.
Example: for DVD VIDEO
Each time you press DISPLAY, the total time display and the
title/chapter number display appear alternately.
To stop playback completely
Press
7
.
Hint
If you press
0
during playback, the player stops playback and
opens the disc tray.
To stop playback temporarily
Press
8
.
To resume playback, press
3
(SELECT). (See the following
item.)
SELECT
ENTER
USE
5∞23
TO SELECT, USE ENTER TO CONFIRM
TO EXIT, PRESS SETUP.
DIGITAL AUDIO OUTPUT
ANALOG DOWN MIX
D RANGE CONTROL
OUTPUT LEVEL
DVD PLAYER SET UP
PCM ONLY
DOLBY DIGITAL/PCM
STREAM/PCM
DIGITAL AUDIO OUTPUT options
• To insert an 8-cm disc, place it in the inner recess.
With the label side up
8.5Mbps
TITLE 33
TOTAL 1:25:58
CHAP 33
Transfer rate
Current chapter
number
Current transport
status
Current title number
Disc elapsed time
Total time
Title number
Chapter number