Jenn-Air JB36NXFXRE Dimension Guide - Page 4

FRONT VIEW, Reverse Osmosis Water Supply, BACK VIEW

Page 4 highlights

C M D N JENN-AIR® DETAILED PLANNING DIMENSIONS O 4 of 4 P 36" FULLY INTEGRATED BOTTOM-FREEZER REFRIGERATORS Q (BASE UNIT REQUIRES SUITE-COORDINATING PANEL KIT OR CUSTOM PANELS AND HANDLES) R JB36NXFXRE, JB36NXFXLE - E353⁄4" x 831⁄8" x 24" (without door/handles) F G 110º OPENING/CLEARANCE DIMENSIONS eH A* I B J K B D E Water Shutoff JB36NXFXR/LW C FRONT VIEW w C F MODEL # JB36NXFXRE JB36NXFXLE in cm A* Width (min.) 36 91.4 B Width of recommended electrical location 4 10.2 Distance from side of cabinet to C recommended water connection location 6 15.2 D Height (min.) 84 213.4 E Height to recommended electrical location 77 195.6 F Depth of recommended water connection location (max.) 1 2.5 e Recommended electrical conEneFction location w Recommended water connectionGlocation *Minimum width must extend behind the faceHof the cabinet for at least 2" (5.1 cm). I ELECTRICAL REQUIREMENTS 115 volt, 60 Hz, AC only, 15- or 20-amp fused, grounded circuit is required. A dedicated circuit is recommended. Use an outlet that cannot be turned off by a switch. Do not use an extension cord. WATER PRESSURE REQUIREMENTS A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa) is required to operate the ice maker. Call a licensed, qualified plumber with any questions about the water pressure. Reverse Osmosis Water Supply IMPORTANT: The pressure of the water coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needsCto* be between 30 and 120 psi (207 and 827 kPa). D* If a reverse osmosis water filtration system is connected to the cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa). LOCATION REQUIREMENTS Floor must be able to support refrigerator (more than 600 lb [272 kg]), door panels andA*contents of the refrigerator and must be at the same level as flooring inBth* e room. Floor BACK VIEW IMPORTANT: Dimensional specifications are provided for planning purposes only. Do not make any cutouts based on this information. Refer to the Installation or Use & Care Guide before selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation. All Jenn-Air® appliances are appropriately UL, CUL or CSA approved. 8107AdZw714

  • 1
  • 2
  • 3
  • 4

IMPORTANT:
Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information.
Refer to the Installation or Use & Care Guide
before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air
®
appliances are appropriately UL, CUL or CSA approved.
JENN-AIR
®
DETAILED PLANNING DIMENSIONS
4 of 4
8107AdZw714
w
D
A*
F
C
C
B
E
e
Water
Shutoff
OPENING/CLEARANCE DIMENSIONS
FRONT VIEW
36" FULLY INTEGRATED BOTTOM-FREEZER REFRIGERATORS
(BASE UNIT REQUIRES SUITE-COORDINATING PANEL KIT OR CUSTOM PANELS AND HANDLES)
JB36NXFXRE, JB36NXFXLE – 35
3
4
" x 83
1
8
" x 24" (without door/handles)
MODEL #
JB36NXFXRE
JB36NXFXLE
in
cm
A*
Width (min.)
36
91.4
B
Width of recommended electrical
location
4
10.2
C
Distance from side of cabinet to
recommended water connection
location
6
15.2
D
Height (min.)
84
213.4
E
Height to recommended electrical
location
77
195.6
F
Depth of recommended water
connection location (max.)
1
2.5
e
Recommended electrical connection location
w
Recommended water connection location
*Minimum width must extend behind the face of the cabinet for at
least 2" (5.1 cm).
ELECTRICAL REQUIREMENTS
115 volt, 60 Hz, AC only, 15- or 20-amp fused, grounded circuit is
required. A dedicated circuit is recommended. Use an outlet that cannot
be turned off by a switch. Do not use an extension cord.
WATER PRESSURE REQUIREMENTS
A cold water supply with water pressure between 30 and 120 psi (207
and 827 kPa) is required to operate the ice maker. Call a licensed,
qualified plumber with any questions about the water pressure.
Reverse Osmosis Water Supply
IMPORTANT:
The pressure of the water coming out of a reverse osmosis
system going to the water inlet valve of the refrigerator needs to be
between 30 and 120 psi (207 and 827 kPa).
If a reverse osmosis water filtration system is connected to the cold water
supply, the water pressure to the reverse osmosis system needs to be a
minimum of 40 to 60 psi (276 to 414 kPa).
LOCATION REQUIREMENTS
Floor must be able to support refrigerator (more than 600 lb [272 kg]),
door panels and contents of the refrigerator and must be at the same
level as flooring in the room.
BACK VIEW