Jenn-Air JB36SSFXLA Installation Instruction - Page 23

Install Overlay Series Custom Panels

Page 23 highlights

After moving the refrigerator to its final location: 1. Use a socket driver to turn the leveling bolts clockwise to extend the legs to the floor as shown. The rollers should be off the floor. A AB B A. Rear leveling bolt B. Front leveling bolt 2. Adjust the leveling legs to level and align the refrigerator from left to right and front to back so that the refrigerator is level and aligned with the cabinetry. The cabinetry surface must be plumb for the ideal fit of the refrigerator side trim. 3. Continue adjusting all of the leveling legs to raise the refrigerator until the top is within at least 1" (2.54 cm) of the top soffit. NOTE: If an anti-tip board has been used, adjust the leveling legs until the top of the refrigerator is within ¹⁄₄" (6.35 mm) of the bottom of the anti-tip board as shown. Do not crush the compressor cover. A B Install Overlay Series Custom Panels IMPORTANT: ■ Install the custom handles prior to installing the panels on the refrigerator. For more information on Jenn-Air custom handle selection, refer to the Jenn-Air Catalog, visit www.jennair.com, or call 1-800-JENNAIR (1-800-536-6247). In Canada, visit www.jennair.ca, or call 1-800-807-6777. ■ Create custom door overlay panels according to the specifications in the "Overlay Series Custom Panels" section. ■ Jenn-Air is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service. Door Panel Installation 1. Remove all tape and door bracing from the refrigerator door(s) and freezer drawer. 2. Open the refrigerator door(s) and freezer drawer and remove the trims and corner caps on each door as shown. A A B B 2" (5 cm) C ¹⁄₄" (6 mm) max. C D A A A. Center board ¹⁄₄" (6.35 mm) max. above refrigerator B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards C. Attach to studs with six #8 x 3" (7.6 cm) screws D. Compressor cover A. Corner caps B. Refrigerator door trims IMPORTANT: Adjust in small increments to keep from C. Freezer drawer trim damaging the cabinet trim and causing problems with the door alignment or top grille fit. To avoid damage to the cabinet or leveling legs, do not apply more than 50 inch-pounds (5.65 Nm) of torque to the leveling bolts. The leveling legs can be extended to a maximum of 1¹⁄₄" (3.18 cm) below the rollers. 4. For Overlay models, additional adjustments may be needed after the custom panels are installed. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80

23
After moving the refrigerator to its final location:
1.
Use a
⁵⁄₁₆
" socket driver to turn the leveling bolts clockwise to
extend the legs to the floor as shown. The rollers should be off
the floor.
2.
Adjust the leveling legs to level and align the refrigerator from
left to right and front to back so that the refrigerator is level
and aligned with the cabinetry. The cabinetry surface must be
plumb for the ideal fit of the refrigerator side trim.
3.
Continue adjusting all of the leveling legs to raise the
refrigerator until the top is within at least 1" (2.54 cm) of the
top soffit.
NOTE:
If an anti-tip board has been used, adjust the leveling
legs until the top of the refrigerator is within
¹⁄₄
" (6.35 mm) of
the bottom of the anti-tip board as shown. Do not crush the
compressor cover.
IMPORTANT:
Adjust in small increments to keep from
damaging the cabinet trim and causing problems with the
door alignment or top grille fit. To avoid damage to the cabinet
or leveling legs, do not apply more than 50 inch-pounds
(5.65 Nm) of torque to the leveling bolts. The leveling legs can
be extended to a maximum of 1
¹⁄₄
" (3.18 cm) below the rollers.
4.
For Overlay models, additional adjustments may be needed
after the custom panels are installed.
Install Overlay Series Custom Panels
IMPORTANT:
Install the custom handles prior to installing the panels on the
refrigerator. For more information on Jenn-Air custom handle
selection, refer to the Jenn-Air Catalog, visit
www.jennair.com
, or call
1-800-JENNAIR (1-800-536-6247)
.
In Canada, visit
www.jennair.ca
, or call
1-800-807-6777
.
Create custom door overlay panels according to the
specifications in the “Overlay Series Custom Panels” section.
Jenn-Air is not responsible for the removal or addition of
molding or decorative panels that would not allow access to
the refrigerator for service.
Door Panel Installation
1.
Remove all tape and door bracing from the refrigerator door(s)
and freezer drawer.
2.
Open the refrigerator door(s) and freezer drawer and remove
the trims and corner caps on each door as shown.
A. Rear leveling bolt
B. Front leveling bolt
A. Center board
¹⁄₄
" (6.35 mm) max. above refrigerator
B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards
C. Attach to studs with six #8 x 3" (7.6 cm) screws
D. Compressor cover
A
B
A
B
B
A
C
2" (5 cm)
D
¹⁄₄
" (6 mm)
max.
A. Corner caps
B. Refrigerator door trims
C. Freezer drawer trim
B
A
B
A
C
A
A