Jenn-Air JED3536GB Dimension Guide - Page 2

_____ JENN-AIR® DETAILED PL ANNING DIMENSIONS _____2____o___f___4 3____6____"____J__X____3 E____L____E__C____T____R____I C______R____A____D____I__A____N____T____D____O______W____N____D______R__A____F____T____C____O____O______K____T__O____P_____ __________J_E_D__3_5__3_6_G___-__3_6_5_⁄1_6_"_x__1_7__59_⁄6_4_"_x__2__3 _____ __ __________O__P__E_N__I_N_G__/_C_L__E_A__R_A__N__C_E__D__I_M__E_N__S_I_O__N__S M__O__D_E__L J_E_D__3_5_3__6_G _____in________c_m A Width of combustible area above cooking surface (min.) 36 91.4 B Width from cooktop to fixed wall or other combustible material (min.) 21⁄2 6.4 C Width to center of vent opening option (min.) 1411⁄16 37.3 A E* B F B D Width to oSiudeter edge of outlet (min.) E* Height toCabbionetttom of uncovered wood or metal cabinJet above cooking surface (min.) F Height to bottom of uncovered wood or metal cabinet (min.) G Height to centKer of vent opening option H Height to top edge of outlet (min.) 10 25.4 30 76.2 18 1313⁄16 12 45.7 35.1 30.5 G v C I** H e D I** Depth to center of vent opening option J Depth of upper cabinet (recommended) K Depth from cutout to wall (min.) L Width of cutout M Depth of cutout N Depth from cutout to front of countertop (min.) 1617⁄64 13 11⁄2 349⁄16 211⁄8 2 41.3 33.0 3.8 87.8 53.7 5.1 v C FRONT VIEW e Recommended electrical access location v Recommended venting location - see page 3-4 for ducting information *Dimension can be reduced by 6" (15.2 cm) when bottom of wood or metal cabinet is covered by not less than 1⁄4" (0.6 cm) flame retardant millboard covered with not less than No. 28 MSG sheet metal, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper. **Based on installation in a 24" (61.0 cm) deep by 341⁄2" (87.6 cm) high base cabinet with a 11⁄2" (3.8 cm) thick counter top. ELECTRICAL REQUIREMENTS 220 volt, 60 Hz, AC only, 40-amp fused, electrical circuit is required. A dedicated circuit is recommended. VENTING REQUIREMENTS This cooktop must be exhausted outdoors unless using the duct-free filter kit (JDA7000WX). Refer to kit instructions for further information. Side Cabinet J F K LOCATION REQUIREMENTS • To ensure cooktop base clearance, cabinet side walls need to be wider than the cutout. • A minimum clearance of 6" (15.2 cm) is recommended between the side of the A cooktop and side wall for maximum ventilation performance. • A minimum and cabinet clearance of 2" (5.1 cm) for proper cooling. A 6" is recommended between the blower (15.2 cm) clearance is recommended fEmo*rotor servicing access. • An under counter built-in oven cannot be installed under this cooktop. B L K M G v C I** H e N v SIDE VIEW TOP VIEW - CUTOUT C IMPORTANT: Dimensional specifications are provided for planning purposes only. Do not make any cutouts based on this information. Refer to the Installation or Use & Care Guide before selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation. All Jenn-Air® appliances are appropriately UL, CUL or CSA approved. 8988dZw117