Jenn-Air JGCP536WP Dimension Guide - Page 1
Jenn-Air JGCP536WP Manual
View all Jenn-Air JGCP536WP manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Commercial Style Gas Cooktop PRODUCT MODEL NUMBERS PRODUCT DIMENSIONS JGCP430W JGCP536W JGCP436W JGCP548W Type of Gas Natural Gas: This cooktop is design-certified by CSA International for use with Natural gas or, after proper conversion, for use with LP gas. q This cooktop is factory-set for use with Natural gas. To convert to LP gas, see the Gas Conversion instructions provided in the package containing literature. The model/ serial rating plate located on the left underside of the cooktop burner base has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier. LP Gas conversion: Conversion must be done by a qualified service technician. No attempt shall be made to convert the cooktop from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. To convert to LP gas, use the LP gas converision kit provided with the cooktop and see the "Gas Conversions" section. Electrical: q A 120 volt, 60 Hz, AC only, 15-amp, fused electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this cooktop be provided. q Electronic ignition systems operate within wide voltage limits, but proper grounding and polarity are necessary. Check that the outlet provides 120-volt power and is correctly grounded. LOCATION REQUIREMENTS IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air. q It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the underside of the cooktop burner base. q It is recommended that a 600 CFM or larger vent hood be installed above the cooktop. q It is not recommended that a microwave hood combination be mounted above the cooktop. q The cooktop should be installed in a location away from strong draft areas, such as windows, doors and strong heating vents or fans. q All openings in the wall or floor where cooktop is to be installed must be sealed. q Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances. q Grounded electrical supply is required. See "Electrical Requirements" section. q Proper gas supply connection must be available. See "Gas Supply Requirements" section. q The cooktop is designed to hang from the countertop by its side or rear flanges. q The gas and electric supply should be located as shown in "Gas and Electric Connection Locations" section so that they are accessible without requiring removal of the cooktop. q Provide cutout in left rear corner of cutout enclosure as shown to provide clearance for gas inlet, power supply cord, and to allow the rating label to be visible. IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. Mobile Home - Additional Installation Requirements The installation of this cooktop must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or local codes. In Canada, the installation of this cooktop must conform with the current standards CAN/CSA-A240-latest edition, or with local codes. A B E C D A. 27¹⁄₈" (68.9 cm) B. 30" (76.2 cm) cooktop: 29⁷⁄₈" (75.1 cm) actual width 36" (91.4 cm) cooktop: 35⁷⁄₈" (90.4 cm) actual width 48" (121.9 cm) cooktop: 47⁷⁄₈" (120.8 cm) actual width C. Island trim or optional backguard D. 36" (91.4 cm) long 3 prong groundingtype power supply cord E. Model/serial rating plate (located on the underside of the cooktop burner base) Side View of Cooktop A B C G E F A. 27¾" (70.5 cm) B. 1¼" (3.2 cm) C. 7 18.8 cm) D. Gas inlet is located 1⁷⁄₈" (4.8 cm) from the back of the cooktop burner base and 4⁷⁄₈" (12.4 cm) in from left-hand side of the cooktop burner base. D E. 22" (55.9 cm) F. 3 8.4 cm) G 1.4 cm) Page 1 of 2 Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation our products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice. Ref. W10145395 03/05/2010