Jenn-Air JGD8348CDP Use and Care - Page 7

6

U

SING

THE

G

RILL

•

Before the first use, wash grill grates in

hot soapy water, rinse and dry.

Then

“season” the surface by wiping on a

thin coating of cooking oil.

Remove

excess oil by wiping with paper towel.

This procedure should be repeated

when either:

a)

cleaning in the

dishwasher since the detergent may

remove seasoning or

b)

anytime a

sugar-based marinade (for example,

barbecue sauce) is going to be used.

•

Preheat the grill on

Hi

for 5 minutes.

Preheating improves the flavor and

appearance of meats and quickly sears

the meat to help retain the juices.

•

Use nonmetallic spatulas or utensils to

prevent damaging the nonstick grill grate

finish.

•

Excessive amounts of fat should be

trimmed from meats.

Only a normal

amount is necessary to produce the

smoke needed for that smoked,

“outdoor” flavor. Excessive fat can

create cleaning and flare-up problems.

•

Allowing excessive amounts of grease

or drippings to constantly flare-up voids

the warranty on the grill grates.

•

Excessive flare-ups indicate that either

the grill interior needs to be cleaned or

that excessive amounts of fat are in the

meat or the meat was not properly

trimmed.

•

Grease drippings will occasionally

ignite to produce harmless puffs of

flame for a second or two.

This is a

normal part of the cooking process.

•

NEVER LEAVE GRILL UNATTENDED

DURING GRILL OPERATION.

S

EALED

B

URNER

C

ARTRIDGES

TO INSTALL SEALED BURNER

CARTRIDGE:

1.

Be sure control knobs are turned

OFF

.

2.

Clean

basin

of

any

grease

accumulation.

(See page 9 for cleaning

recommendations.)

3.

With the back raised, position the burner

cartridge with the mixer tube openings

and ignitor rods toward the orifices

and terminal receptacle. Slide the

cartridge until the tubes and ignitors

start to engage, then lower the cartridge

so that it rests on the cooktop surface.

Gently slide forward to fully engage.

TO REMOVE SEALED BURNER

CARTRIDGE:

1.

Control knobs should be in the

OFF

position and the cooktop should be

cool.

2.

Lift up the rear edge of the cartridge

until the bottom of the cartridge clears

the basin. (Lifting the cartridge too

high while still engaged could damage

the ignitor rods and mixer tubes.)

3.

To disengage the cartridge, hold by the

sides and pull away from the terminal

receptacle and orifices. Lift out when

fully unplugged.

4.

Do not stack cartridges where they

may fall or be damaged.

NOTE:

Optional Sealed Burner

Cartridge, model JGA8100, can replace

the grill burner assembly.

G

RILL

I

NSTALLATION

The grill assembly consists of two grill

grates and a grill burner. Only install the

grill on the LEFT SIDE of your cooktop.

TO INSTALL GRILL:

1.

Before installing grill components, be

sure controls knobs are in the

OFF

position.

2.

Position the grill burner with mixer

tubes and ignitor rod toward the orifices

and terminal receptacle. Slide the

burner until the tubes and ignitor

engage, then lower the burner until it

rests on the mounting pins.

3.

Place the grill grates on top of the

cooktop.

NOTE:

Before using the grill for the

first time, heat the grill burner to remove

the protective shipping coating. Heat

the grill burner on

Hi

for 10 minutes

and use the vent system to remove any

additional smoke during cooling.

TO REMOVE GRILL:

1.

Be sure control knobs are in the

OFF

position and the grill components are

cool.

2.

Remove grill grates.

3.

Lift the rear of the burner up slightly.

Slide the burner away from the orifices

and terminal receptacle.

Cont.

Jenn-Air JGD8348CDP Use and Care - Page 7

Ealed, Urner, Artridges, Nstallation - burner cartridge

Page 7 highlights