Jenn-Air JJD3024HL1 Installation Instructions - Page 6

Complete Installation

Get Jenn-Air JJD3024HL1 PDF manuals and user guides View all Jenn-Air JJD3024HL1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Install the Coffee System WARNING Excessive Weight Hazard Use two or more people to move and install the built-in coffee system. Failure to do so can result in back or other injury. 7. Secure the power supply cord with the power supply cord clip. Make sure there is enough slack in the power supply cord to allow the coffee system to be pulled completely from the cabinet in order to fill the coffee bean container. WARNING 1. Pull the runners forward until they are fully extended. 2. Using 2 or more people, position the coffee system onto the runners, making sure that the 2 hooks on the back of the mounting brackets are inside the holes on the rear/back/ bottom of the coffee system. Pull runners all the way forward and in the locked position, and lock into place using the 'orange locking tabs'. Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 8. Plug the coffee system into a grounded 3-prong outlet. 9. Push the coffee system back into the housing. 10. Proceed to "Complete Installation" section. Complete Installation 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. 3. Dispose of/recycle all packaging materials. 3. Secure the coffee system to the runners with the two, 3/16" x 3/8" (4.2 x 9.5 mm) screws. 4. Position the power supply cord clip on the top of the cabinet, approximately 13ZZ/zn" (34.8 cm) from the front of the cabinet and centered from left to right. With a pencil, mark the hole through the clip on the top of the cabinet. 5. Using a 1/16" (2 mm) drill, drill the hole marked in Step 4. 6. Using one 3/16" x 5/8" (4.5 x 16 mm) screw, attach the power supply cord clip to the top of the cabinet. A B If you need Assistance or Service: Please reference the "Assistance or Service" section of the Use and Care Guide or contact the dealer from whom you purchased your trim kit. Approx. 13 34.8 cm) A. Power supply cord clip B. Power supply cord 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
6
Install the Coffee System
1.
Pull the runners forward until they are fully extended.
2.
Using 2 or more people, position the coffee system onto the
runners, making sure that the 2 hooks on the back of the
mounting brackets are inside the holes on the rear/back/
bottom of the coffee system. Pull runners all the way forward
and in the locked position, and lock into place using the
'orange locking tabs'.
3.
Secure the coffee system to the runners with the two,
3/16" x 3/8" (4.2 x 9.5 mm) screws.
4.
Position the power supply cord clip on the top of the cabinet,
approximately 13
ZZ
/
zn
" (34.8 cm) from the front of the
cabinet and centered from left to right. With a pencil, mark
the hole through the clip on the top of the cabinet.
5.
Using a 1/16" (2 mm) drill, drill the hole marked in Step 4.
6.
Using one 3/16" x 5/8" (4.5 x 16 mm) screw, attach the power
supply cord clip to the top of the cabinet.
7.
Secure the power supply cord with the power supply cord
clip. Make sure there is enough slack in the power supply
cord to allow the coffee system to be pulled completely from
the cabinet in order to fill the coffee bean container.
8.
Plug the coffee system into a grounded 3-prong outlet.
9.
Push the coffee system back into the housing.
10.
Proceed to “Complete Installation” section.
Complete Installation
1.
Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
2.
Check that you have all of your tools.
3.
Dispose of/recycle all packaging materials.
If you need Assistance or Service:
Please reference the “Assistance or Service” section of the Use
and Care Guide or contact the dealer from whom you purchased
your trim kit.
WARNING
Excessive Weight Hazard
Use two or more people to move and install the built-in
coffee system.
Failure to do so can result in back or other injury.
A. Power supply cord clip
B. Power supply cord
Approx.
13¹¹
/
₁₆
"
(34.8 cm)
A
B
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING