Jenn-Air JJD3024HL1 Dimension Guide - Page 4

Jennair, Small Warming Drawers - Flush Installation, Opening/clearance Dimensions

Get Jenn-Air JJD3024HL1 PDF manuals and user guides View all Jenn-Air JJD3024HL1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

DETAILED PLANNING DIMENSIONS 4 of 4 JENNAIR® SMALL WARMING DRAWERS - FLUSH INSTALLATION JJD3024H - 23M/zn" x 5>/zn" x 22C/," OPENING/CLEARANCE DIMENSIONS D C* A B 3/4" (2 cm) Side Cleats* 5/8" (1.6 cm) Support Surface* e FRONT VIEW Back of Cabinet MODEL # JJD3024HM JJD3024HL in cm in cm A Width of flush inset cutout (min.) 2311⁄16 60.2 2311⁄16 60.2 B Width of opening 2111⁄16 55 2111⁄16 55 (min.) C* Height of opening (min.) 2215⁄16 58.2 2215⁄16 58.2 D Height of flush 233⁄4 60.3 233⁄4 60.3 inset cutout (min.) E Depth of cutout (min.) 2111⁄16 - 221⁄2 55 - 57.2 2111⁄16 - 229⁄16 55 - 57.3 e Recommended outlet location *Height for installation of JJD3024 under JJW6024, JMC6224 or JJB6424 ELECTRICAL REQUIREMENTS 120 V, 60 Hz, AC only, 15 A fused, electrical circuit is required. A dedicated circuit is recommended. If the outlet is on the rear wall behind the warming drawer, it must be recessed and located in the upper right-hand corner. If outlet is located in an adjacent cabinet, drill a 13⁄8" (3.5 cm) minimum diameter hole in the side wall or support surface to access the power supply cord. LOCATION REQUIREMENTS Support surface must be solid and level with the bottom of the cabinet cutout. The warming drawer must be leveled before completing installation. FLUSH INSTALLATION REQUIREMENTS A 229⁄16" (57.3 cm) minimum cutout depth is required. These dimensions will result in a 1/8" (3 mm) reveal on all sides of the warming drawer. The front face of the cleats and platforms will be visible and should be treated as a finished surface. E SIDE VIEW E Side Cleat* 13/16" (2.1 cm) for NOIR™ and RISE™ Power cord location TOP VIEW BACK VIEW *Cleats and platform must be recessed 13/16" (2.1 cm) for NOIR™ and 7/8" (2.2 cm) for RISE™ from the front of the cabinet. IMPORTANT: Dimensional specifications are provided for planning purposes only. Do not make any cutouts based on this information. Refer to the Installation Guide before selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation. All JennAir® appliances are appropriately UL, CUL or CSA approved. ®/™ ©2019 JennAir. All rights reserved. W11308123B Installation Instruction W11260097

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
JENNAIR
®
SMALL WARMING DRAWERS - FLUSH INSTALLATION
JJD3024H – 23
M
/
zn
" x 5
>
/
zn
" x 22
C
/
,
"
OPENING/CLEARANCE DIMENSIONS
DETAILED PLANNING DIMENSIONS
e
A
D
C*
B
3/4
(2 cm)
Side Cleats*
(1.6 cm)
Support Surface*
5/8"
"
FRONT VIEW
MODEL
#
JJD3024HM
JJD3024HL
in
cm
in
cm
A
Width of flush
inset cutout (min.)
23
11
⁄
16
60.2
23
11
⁄
16
60.2
B
Width of opening
(min.)
21
11
⁄
16
55
21
11
⁄
16
55
C*
Height of opening
(min.)
22
15
⁄
16
58.2
22
15
⁄
16
58.2
D
Height of flush
inset cutout (min.)
23
3
⁄
4
60.3
23
3
⁄
4
60.3
E
Depth of cutout
(min.)
21
11
⁄
16
- 22
1
⁄
2
55 - 57.2
21
11
⁄
16
-
22
9
⁄
16
55 - 57.3
e
Recommended outlet location
*Height for installation of JJD3024 under JJW6024, JMC6224 or JJB6424
IMPORTANT:
Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information.
Refer to the Installation Guide before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All JennAir
®
appliances are appropriately UL, CUL or CSA approved.
®
/™ ©2019 JennAir. All rights reserved.
W11308123B
Installation Instruction W11260097
Back of Cabinet
E
Power cord location
SIDE VIEW
BACK VIEW
ELECTRICAL REQUIREMENTS
120 V, 60 Hz, AC only, 15 A fused, electrical circuit is required. A
dedicated circuit is recommended.
If the outlet is on the rear wall behind the warming drawer, it must be
recessed and located in the upper right-hand corner. If outlet is located
in an adjacent cabinet, drill a 1
3
⁄
8
" (3.5 cm) minimum diameter hole in the
side wall or support surface to access the power supply cord.
LOCATION REQUIREMENTS
Support surface must be solid and level with the bottom of the cabinet
cutout.
The warming drawer must be leveled before completing installation.
FLUSH INSTALLATION REQUIREMENTS
A 22
9
⁄
16
" (57.3 cm) minimum cutout depth is required.
These dimensions will result in a 1/8" (3 mm) reveal on all sides of the
warming drawer.
The front face of the cleats and platforms will be visible and should be
treated as a finished surface.
E
Side Cleat*
13/16" (2.1 cm) for NOIR
™
and RISE
™
TOP VIEW
*Cleats and platform must be recessed 13/16" (2.1 cm) for NOIR
™
and
7/8" (2.2 cm) for RISE
™
from the front of the cabinet.
4 of 4