Jenn-Air JJW2427IL1 Installation Instructions - Page 16

Complete Installation, Install Deflector Kit, Check Operation of Single and Double Ovens

Get Jenn-Air JJW2427IL1 PDF manuals and user guides View all Jenn-Air JJW2427IL1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Install Deflector Kit 1. Flex the upper vent piece (C) away from the lower vent piece (D) to slide the warming drawer deflector (B) between them. Some force may be required to flex the upper vent trim (C) away from the lower vent trim (D). Some force may also be required to flex the warming drawer deflector (B) and slide it into position. Make sure screw holes are properly aligned between the two pieces. See the following illustration. 2. Install the warming drawer deflector (B) to the lower vent piece (D) using two #8-18 x 1/4" (6.4 mm) screws on each side. NOTE: On 27" (68.6 cm) models, only one #8-18 x 1/4" (6.4 mm) screw is used on each side. A B C B D C D A. #8-18 x 1/4" (6.4 mm) screws C. Upper vent piece B. Warming drawer deflector D. Lower vent piece 3. Align vent tab (B) with oven frame (A) as shown in the following illustration. 4. Using one #8-18 x 3/8" (9.5 mm) screw (E) on each side of the vent tab (B), fasten the vent securely to the oven. Complete Installation 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. 3. Dispose of/recycle all packaging materials. 4. For oven use and cleaning, read the Use and Care Guide. Check Operation of Single and Double Ovens 1. Turn on power. 2. At first use, set up the clock and any other preferences, if available. For more information, read the Use and Care Guide. 3. Press BROIL on single oven models. NOTE: Press UPPER BROIL or LOWER BROIL on double oven models. 4. Set the temperature. 5. Press START. If Oven(s) Does Not Operate, Check the Following: ■■ Household fuse is intact and tight, or circuit breaker has not tripped. ■■ Electrical supply is connected. ■■ See "Troubleshooting" section in the Use and Care Guide. 6. When oven has been on for 5 minutes, feel for heat. If you do not feel heat or if an error message appears in the display, turn off the oven and contact a qualified technician. 7. Press UPPER CANCEL/LOWER CANCEL on double ovens, or press CANCEL on single ovens. If You Need Assistance or Service: Please reference the "Warranty." A E D A. Oven frame B. Vent tab C. Oven vent B C D. Warming drawer deflector E. #8-18 x 3/8" (9.5 mm) screw

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
Install Deflector Kit
1.
Flex the upper vent piece (C) away from the lower vent piece
(D) to slide the warming drawer deflector (B) between them.
Some force may be required to flex the upper vent trim (C)
away from the lower vent trim (D). Some force may also be
required to flex the warming drawer deflector (B) and slide
it into position. Make sure screw holes are properly aligned
between the two pieces. See the following illustration.
2.
Install the warming drawer deflector (B) to the lower vent
piece (D) using two #8-18 x 1/4" (6.4 mm) screws on each
side.
NOTE:
On 27" (68.6 cm) models, only one #8-18 x 1/4"
(6.4 mm) screw is used on each side.
3.
Align vent tab (B) with oven frame (A) as shown in the
following illustration.
4.
Using one #8-18 x 3/8" (9.5 mm) screw (E) on each side of
the vent tab (B), fasten the vent securely to the oven.
Complete Installation
1.
Check that all parts are now installed. If there is an extra
part, go back through the steps to see which step was
skipped.
2.
Check that you have all of your tools.
3.
Dispose of/recycle all packaging materials.
4.
For oven use and cleaning, read the Use and Care Guide.
Check Operation of Single and Double Ovens
1.
Turn on power.
2.
At first use, set up the clock and any other preferences,
if available. For more information, read the Use and
Care Guide.
3.
Press BROIL on single oven models.
NOTE:
Press UPPER BROIL or LOWER BROIL on double
oven models.
4.
Set the temperature.
5.
Press START.
If Oven(s) Does Not Operate, Check the Following:
■
Household fuse is intact and tight, or circuit breaker
has not tripped.
■
Electrical supply is connected.
■
See “Troubleshooting” section in the Use and Care
Guide.
6.
When oven has been on for 5 minutes, feel for heat. If you
do not feel heat or if an error message appears in the display,
turn off the oven and contact a qualified technician.
7.
Press UPPER CANCEL/LOWER CANCEL on double ovens,
or press CANCEL on single ovens.
If You Need Assistance or Service:
Please reference the “Warranty.”
D
B
A
C
B
D
C
A. #8-18 x 1/4" (6.4 mm) screws
B. Warming drawer deflector
C. Upper vent piece
D. Lower vent piece
A
C
D
B
E
A. Oven frame
B. Vent tab
C. Oven vent
D. Warming drawer deflector
E. #8-18 x 3/8" (9.5 mm)
screw