Jenn-Air JJW3430WP Dimension Guide - Page 3

Opening/clearance Dimensions - jjw3430ws oven

Get Jenn-Air JJW3430WP PDF manuals and user guides View all Jenn-Air JJW3430WP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

JENN-AIR® DETAILED PLANNING DIMENSIONS 30" single wall ovens JJW3430W, JJW2430W, JJW2330W - 293⁄4" x 291⁄2" x 263⁄4" 3 of 5 OPENING/CLEARANCE DIMENSIONS A A A D D D C* C* B C* B B E E E G e e e F F F FRONT VIEW A H A I e e A A e C*e J C* H H B CK* L B H MB Side VIEW e e MODEL # JJW3430W JJW2430W JJW2330W in cm A Width of cabinet (min.) 30 76.2 B Width of cutout 281⁄2 72.4 C* Height of cutout (recommended) 273⁄4 70.5 D Top of cutout to bottom of upper cabinet door (min.) 2 5.1 E Bottom of cutout to top of lower cabinet door (min.) 11⁄2 3.8 F Bottom of cutout to floor 45⁄8- 11.732 81.3 G Depth of cutout (min.) 24 61.0 H Bottom of countertop to bottom of cutout (min.) 301⁄2 77.5 e Recommended junction box location *Will fit cutout height from 27" (68.6 cm) to 291⁄16" (73.8 cm). ELECTRICAL REQUIREMENTS G240 volt, 20-amp fused, grounded circuit is required. A dedicated circuit is recommended. G The length of conduit provided is for serviceability. Do not cut the conduit. The junction box should be located 3" (7.6 cm) maximum below the support surface. Drill a 11⁄4" (3.4 cm) minimum diameter hole in the right rear corner of the support surface for access to the junction box. If the junction box is on the rear wall behind the oven, it must be recessed and located in any corner of the cabinet. NOTE: For under counter installation, the junction box should be located in the adjacent right or left cabinet. Drill a 11⁄4" (3.4 cm) minimum diameter hole in an upper corner of the side wall for access to the junction box. CABINET REQUIREMENTS NOTE: When using under counter installation, check cabinet manufacturer's specifications to verify fit. Power Supply Location F F F Under counter Installation (without cooktop installed above) Back VIEW Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary. JRC120005 03/2012

  • 1
  • 2
  • 3
  • 4
  • 5
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
JENN-AIR
®
DETAILED PLANNING DIMENSIONS
3 of 5
JRC120005
03/2012
OPENING/CLEARANCE DIMENSIONS
FRONT VIEW
SIDE VIEW
UNDER COUNTER INSTALLATION
(without cooktop installed above)
BACK VIEW
Power Supply
Location
30" SINGLE WALL OVENS
JJW3430W, JJW2430W, JJW2330W – 29
3
⁄
4
" x 29
1
⁄
2
" x 26
3
⁄
4
"
A
B
C*
e
E
D
F
G
B
C*
e
e
F
A
H
MODEL #
JJW3430W
JJW2430W
JJW2330W
in
cm
A
Width of cabinet (min.)
30
76.2
B
Width of cutout
28
1
⁄
2
72.4
C*
Height of cutout (recommended)
27
3
⁄
4
70.5
D
Top of cutout to bottom
of upper cabinet door (min.)
2
5.1
E
Bottom of cutout to top
of lower cabinet door (min.)
1
1
⁄
2
3.8
F
Bottom of cutout to floor
4
5
⁄
8
-
32
11.7-
81.3
G
Depth of cutout (min.)
24
61.0
H
Bottom of countertop to bottom
of cutout (min.)
30
1
⁄
2
77.5
e
Recommended junction box location
*Will fit cutout height from 27" (68.6 cm) to 29
1
⁄
16
" (73.8 cm).
ELECTRICAL REQUIREMENTS
240 volt, 20-amp fused, grounded circuit is required. A dedicated
circuit is recommended.
The length of conduit provided is for serviceability. Do not cut the
conduit. The junction box should be located 3" (7.6 cm) maximum
below the support surface. Drill a 1
1
⁄
4
" (3.4 cm) minimum diameter
hole in the right rear corner of the support surface for access to the
junction box.
If the junction box is on the rear wall behind the oven, it must be
recessed and located in any corner of the cabinet.
NOTE:
For under counter installation, the junction box should be
located in the adjacent right or left cabinet. Drill a 1
1
⁄
4
" (3.4 cm)
minimum diameter hole in an upper corner of the side wall for
access to the junction box.
CABINET REQUIREMENTS
NOTE:
When using under counter installation, check cabinet
manufacturer’s specifications to verify fit.