Jenn-Air JMC2427IM Installation Instructions - Page 3
Installation Requirements
View all Jenn-Air JMC2427IM manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools Needed ■■ Phillips screwdriver ■■ Flat-blade screwdriver ■■ Measuring tape ■■ Level ■■ Drill (for wall cabinet installations) ■■ 1/8" (3 mm) drill bit (for wall cabinet installations) ■■ 1" (2.5 cm) drill bit (for wall cabinet installations Parts Needed ■■ UL listed or CSA approved conduit connector ■■ UL listed wire connectors Parts Needed - Flush Installation ■■ W10801485 Stainless steel flush installation kit for 27" (68.6 cm) models ■■ W10801486 Stainless steel flush installation kit for 30" (76.2 cm) models ■■ W10801487 Black flush installation kit for 30" (76.2 cm) models To order, see the "Assistance or Service" section of the Use and Care Guide. Parts Supplied A CD ■■ For installation above single built-in oven, the junction box must located inside upper cabinet. ■■ If you are installing the junction box on rear wall behind the microwave oven, the junction box must be recessed and located in the upper or lower right or left corner of the cabinet; otherwise, the microwave oven will not fit into the cabinet opening. ■■ Microwave oven support surface must be solid, level, and flush with bottom of cabinet cutout. Floor must be able to support a weight of 108 lbs (49.0 kg). IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate, or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C). Product Dimensions 27" (68.6 cm) and 30" (76.2 cm) Microwave Ovens A E B D C F B A. Spacer bars (2) B. Bottom vent (1) C. 3/8" (9.5 mm) hex-head washer screws (4) D. 3/4" (1.9 cm) pan-head screws (4) Check local codes. Check existing electrical supply. See "Electrical Requirements." It is recommended that all electrical connections be made by a licensed, qualified electrical installer. Location Requirements IMPORTANT: Observe all governing codes and ordinances. ■■ Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance with microwave oven. ■■ Recessed installation area must provide complete enclosure around the recessed portion of the microwave oven. ■■ Grounded electrical supply is required. See "Electrical Requirements" section. ■■ Electrical supply junction box should be located 3" (7.6 cm) maximum below the support surface when the microwave oven is installed in a wall cabinet. A 1" (2.5 cm) minimum diameter hole should have been drilled in the left rear corner of the support surface to pass the appliance cable through to the junction box. 27" (68.6 cm) models A. 253/8" (64.5 cm) B. 173/8" (44.1 cm) C. 2211/16" (57.7 cm) D. 263/4" (68.0 cm) overall width E. 197/8" (50.3 cm) overall height F. JMC2427IM: 259/16 (64.9 cm) JMC2427IL: 243/4" (62.9 cm) 30" (76.2 cm) models A. 283/8" (72.1 cm) B. 173/8" (44.1 cm) C. 2211/16" (57.7 cm) D. 293/4" (75.6 cm) overall width E. 197/8" (50.3 cm) overall height F. JMC2430IM: 259/16 (64.9 cm) JMC2430IL: 243/4" (62.9 cm) 27" (68.6 cm) and 30" (76.2 cm) Microwave Oven Spacer Kit A 27" (68.6 cm) models A. 263/4" (67.9 cm) overall width 30" (76.2 cm) models A. 293/4" (75.6 cm) overall width NOTE: The microwave oven spacer kit will allow the microwave oven to be installed in a 173/8" to 173/4" (44.1 to 45.1 cm) maximum cutout height. 3