Jenn-Air JXI8036WS Dimension Guide - Page 1

36" (91.4 cm) and 42" (106.7 cm) Island Canopy Range Hood PRODUCT MODEL NUMBERS JXI8036W JXI8042W ELECTRICAL REQUIREMENTS • A 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical circuit is required. VENTING METHODS This island hood is factory set for venting through the roof. An 8" (20.3 cm) round vent system is needed for installation (not included). The hood exhaust opening is 8" (20.3 cm) round. NOTE: Flexible vent is not recommended. Flexible vent creates back pressure and air turbulence that greatly reduce performance. Vent system can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed. For Non-Vented (recirculating) Installations If it is not possible to vent cooking fumes and vapors to the outside, the hood can be used in the non-vented (recirculating) version, fitting a charcoal filter and the deflector. Fumes and vapors are recycled through the top grille. NOTE: Wall venting can be an option for 2-story homes. Roof Venting Non-vented (recirculating) A A B B A. Roof cap B. 8" (20.3 cm) round vent A. Deflector B. 8" (20.3 cm) round vent Calculating Vent System Length To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system. Vent Piece 8" (20.3 cm) Round 45° elbow 2.5 ft (0.8 m) 90° elbow 5.0 ft (1.5 m) Example vent system 90 elbow 6 ft (1.8 m) Wall cap 2 ft (0.6 m) The following example falls within the maximum recommended vent length of 35 ft (10.7 m). 1 - 90° elbow 1 - wall cap 8 ft (2.4 m) straight = 5.0 ft (1.5 m) = 0.0 ft (0.0 m) = 8.0 ft (2.4 m) Length of system = 13.0 ft (3.9 m) LOCATION REQUIREMENTS IMPORTANT: Observe all governing codes and ordinances. Have a qualified technician install the range hood. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located behind the left filter on the rear wall of the vent hood. Canopy hood location should be away from strong draft areas, such as windows, doors and strong heating vents. Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance. Grounded electrical outlet is required. See "Electrical Requirements" section. Because of the size and weight of this island hood, the chimney support must be securely attached to the ceiling. • For plaster or drywall ceilings, the chimney support must be attached to joists. If this is not possible, you must build a support structure behind the plaster or drywall. The support structure must be able to support 80 lbs (36.6 kg). The range hood is factory set for venting through the roof. For non-vented (recirculating) Installation see "Non-vented (recirculating) Installations" in "Install Range Hood" section. Recirculation Kit Part Number W10272061 is available from your dealer or an authorized parts distributor. All openings in ceiling and wall where range hood will be installed must be sealed. For Mobile Home Installations The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes. Maximum equivalent vent length is 35 ft (10.7 m). Because Whirlpool Corporation policy includes a continuous commitment to improve our Dimensions are for planning purposes only. For complete details, see Installation products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice. Page 1 of 2 Ref. W10274319E 12/16/09