Jenn-Air JXW5036WS Dimension Guide - Page 1

30" (76.2cm) and 36" (91.4cm) Wall-Mount Canopy Range Hood PRODUCT MODEL NUMBERS JXW5030W JXW5036W ELECTRICAL REQUIREMENTS q A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required. VENTING REQUIREMENTS This canopy hood is factory set for venting through the roof or wall. A 8" (20.0 cm) round vent system is needed for installation (not included). The hood exhaust opening is 8" (20.0 cm) round. NOTE: Flexible vent is not recommended. Flexible vent creates back pressure and air turbulence that greatly reduce performance. Vent system can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed. Rear discharge A 90° elbow may be installed immediately above the hood. For Non-Vented (recirculating) Installations If it is not possible to vent cooking fumes and vapors to the outside, the hood can be used in the non-vented (recirculating) version, fitting a charcoal filter and the deflector. Fumes and vapors are recycled through the top grille. Roof Venting Wall Venting Non-vented (recirculating) PRODUCT DIMENSIONS 14⁷⁄₈" (37.8 cm) 28" (71.7 cm) 35" (88.9 cm) min. *60³⁄₄" (154.3 cm) max. 56 143.0 cm) max. 19³⁄₄" (50 cm) 12³⁄₄" (32.3 cm) 30" - 36" (76.2 cm - 91.4 cm) *For non-vented (recirculating) installations INSTALLATION DIMENSIONS 11⁷⁄₈" (30 cm) 13 35 cm) *8" (20.3 cm) min. 2" (5.1 cm) min. A. Roof cap B. 8" (20.0 cm) round vent A. Wall cap B. 8" (20.0 cm) round vent A. Deflector B. 8" (20.0 cm) round vent NOTE: Wall venting may not be possible for all installations. Calculating Vent System Length To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system. 14 ¹⁄₄" (36 cm) side cabinet vent and power supply cable entry location 26 68 cm) side cabinet Vent Piece 45° elbow 8" (20.0 cm) Round 2.5 ft (0.8 m) 30" - 36" (76.2 cm - 91.4 cm) "X" bottom of canopy to cooking surface 90° elbow 5.0 ft (1.5 m) Maximum equivalent vent length is 35 ft (10.7 m). Example vent system 90° elbow 6 ft. (1.8 m) 2 ft. (0.6 m) Note: Flexible vent is Not recommended. Maximum length 1 - 90° elbow 8 ft. (2.4 m) straight 1 - wall cap Length of system wall cap = 35 ft. (10.7 m) = 5.0 ft. (1.5 m) = 8.0 ft. (2.4 m) = 0.0 ft. (0 m) =13.0 ft. (3.9 m) centerline cooking surface *For non-vented (recirculating) installations IMPORTANT: Minimum distance "X": 24" (61.0 cm) from electric cooking surface. Minimum distance "X": 27" (68.6 cm) from gas cooking surfaces. Suggested maximum distance "X": 36" (91.4 cm) For vented installations, the chimneys can be adjusted for ceilings between 8' (2.44 m) and 10' 2" (3.1 m). For non-vented (recirculating) installations, the chimneys can be adjusted for ceilings between 8' (2.44 m) and 10' 6" (3.2 m). *NOTE: The range hood chimneys are adjustable and designed to meet varying ceiling or soffit heights depending on the distance "X" between the bottom of the range hood and the cooking surface. For higher ceilings, a Stainless Steel Chimney Extension Kit Part Number W10272071 is available from your dealer or an authorized parts distributor. The chimney extension replaces the upper chimney shipped with the range hood. Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation our products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice. Ref. W10274303D 08/28/2009