Jensen MCD10 Owners Manual - Page 16
Troubleshooting, Specifications, Resolución de Fallas, Especificaciones
![]() |
UPC - 681787011955
View all Jensen MCD10 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 16 highlights
Troubleshooting Problem CD changer does not operate Disc is playing but there is no sound Music "skips" excessively when going over bumps Cause Correction Fuse blown Locate and replace fuse Bad ground to CD changer Locate and repair ground CD changer overheated Allow air to circulate around changer Magazine not installed/no discs in Install discs and magazine magazine/discs installed incorrectly Fuse blown Locate and replace fuse Condensation (moisture) on CD changer laser optics (occurs in humid, rainy conditions or after turning on the heater) Remove magazine, leave CD changer door open and wait approximately one hour Shipping screws not removed Remove shipping screws Vertical/horizontal anti-vibration spring position not selected correctly Select correct position Using the Reset Button Press RESET only when one of these conditions occur: • The compact disc changer is first installed • Vehicle power is interrupted (as when replacing the battery) RESET Button Specifications Frequency Response 20Hz-20kHz (-3dB) Signal to Noise Ratio @ 1kHz 90dB Stereo Separation @ 1kHz 65dB THD+N @ 1kHz 01% Power Supply 14.4VDC (10-16VDC allowable), negative ground Fuse 5 amp (battery), 0.5 (accessory/ignition), glass type, fast blow Dimensions 9 5/8" x 3 3/8" x 7 2/8" (245mm x 85mm x 180mm) Specifications subject to change without notice. MCD10 Resolución de Fallas Problema l cambiador de CD no opera El disco se ejecuta pero no hay sonido Música "salta" demasiado cuando se circula sobre protuberancias Causa Correccione Fusible quemado Localice y reemplace el fusible Mala conexión a tierra del cambiador de CD Localice y repare la conexión a tierra Cambiador de CD se sobrecalienta Permita que circule aire alrededor del cambiador Compartimento no instalado/no hay discos en compartimento/ discos instalados incorrectamente Instale discos y compartimento Fusible quemado Localice y reemplace el fusible Condensación (humedad) en las ópticas láser del cambiador de CD (ocurre en clima húmedo o lluvioso o luego de apagar la calefacción) Quite el compartimento, deje la puerta del cambiador de CD abierta y espere aproximadamente una hora No se quitaron los tornillos de transporte Quite los tornillos de transporte Posición de resortes antivibración Seleccione la posición correcta vertical u horizontal no seleccionados correctamente Utilizando el Botón de RESET (Reinicio) Presione RESET (Reinicio) solamente cuando una de estas condiciones ocurre: • Se instala por primera vez el cambiador de discos compactos. • La energía del vehículo se interrumpe (como cuando se reemplaza la batería) el Botón RESET Especificaciones Frecuencia de Respuesta 20Hz-20kHz (-3dB) Señal a Coeficiente de Ruido @ 1kHz 90dB Separación de Estéreo @ 1kHz 65dB THD+N @ 1kHz 01% Alimentación 14.4VDC (10-16VDC permitida), conexión a tierra Fusible 5 amp (batería), 0.5 (accesorio/encendido), tipo de vidrio, soplo rápido Dimensiones 9 5/8" x 3 3/8" x 7 2/8" (245mm x 85mm x 180mm) Especificaciones sujetas a cambios sin notificación. 16
![](/manual_guide/products/jensen-mcd10-owners-manual-9ded3ba/16.png)