Home » Jensen Manuals » Car Video Devices » Jensen VM9022 » Manual Viewer

Jensen VM9022 Operation Manual - Page 12

Controls And Indicators - default password

UPC - 043258303721

Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

CONTROLS AND INDICATORS Button Operation 1. OPEN Press to activate the automatic mechanical system and move the TFT monitor into viewing position. Press again to close the TFT. 2. DISP/TILT Press to cycle through information available on the TFT screen. In DVD Mode, press to view the top and bottom information bars. Press again to turn "Display Off". Press and hold to activate the screen tilt function (use the joystick to adjust the angle). 3. AS/PS Press to automatically store the first six strong stations in preset memory. Applies to current band only. 4. BAND/LOC/DX Press the BAND button to change the AM, FM or SAT band. Press and hold to turn strong local reception on/off. 5. AUDIO Rotate to adjust the volume. Press to enter and/or confirm audio settings. 6. SRC Press to select playing mode. 7. WIDE/PIC Press to adjust the display aspect of the picture to one of three settings: CINEMA, NORMAL or Standby (screen off). Touch the screen to turn Standy mode off. NOTE: Only CINEMA and Standby are available for non-video sources. Press and hold to adjust Brightness and Contrast. 8. MUTE Press to silence the receiver. Press again to resume the previous volume level. BT Mode: Answer/dial Bluetooth call. NOTE: The VM9022 features Softmute, which will allow the volume to increase or decrease gradually when the MUTE function is activated or deactivated. 9. IR Remote Control Receiver 10. (left joystick) DVD/Disc Mode: Press once to play back the previous chapter/track. TUNER Mode: Press once to auto-search for the previous available radio station. MENU Mode: Press once to move the cursor to the left. 8 VM9022 11. (down joystick) DVD/Disc Mode: Press once for slow forward/slow reverse. TUNER Mode: Press to go down one frequency step. MENU Mode: Press once to move the cursor down. 12. Reset Press to reset system settings to factory default (except the password and parental lock setting).

Section	Page
MEDIALINK AND SATELLITE CONNECTIONS	8
Installation	9
ISO DIN Installation	9
1. Remove the existing factory radio from the dashboard or center console mounting. Save all hardware and brackets as they will be used to mount the new radio.	9
2. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.	9
3. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. Follow the wiring...	9
4. Mount the new radio assembly to the dashboard or center console using the reverse procedure in step 1.	9
Installation Using Half-Sleeve	9
1. Press the metal levers on both sides to remove the half- sleeve from the radio.	9
2. Install the half-sleeve.	9
a. Install adapter if necessary (optional).	9
b. Install half-sleeve into adapter or dashboard (use only the supplied screws). Do not force the sleeve into the opening or cause it to bend or bow.	9
c. Locate the series of bend-tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the sleeve is firmly secured to the dashboard.	9
3. Use the M5 x 6 screws (provided) to install the mounting brackets to each side of the radio using the holes indicated below.	9
4. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve.	9
5. Complete wiring as illustrated in the wiring diagram on page 3. Once the wiring is complete, reconnect the battery negative terminal. If there is no ACC available, connect the ACC lead to the power supply with a switch.	10
1. Connect wiring adapter to existing wiring harness.	10
2. Connect antenna lead.	10
3. Carefully slide the radio into the half-sleeve, making sure it is right-side-up, until it is fully seated and the spring clips lock it into place.	10
Using the Cosmetic Trim Ring	10
Installing the MediaLink External AV Connector	10
Replacing the Fuse	10
Anti-Theft Feature	11
Entering the Default Password	11
Changing the Password	11
1. Press the SETUP button (31) on the remote control or touch the button on the screen to enter the “SETUP” menu.	11
2. Touch RATING to view the “RATING” sub-menu. An open lock icon to the right of the “Password” field indicates that a user password had not yet been entered.	11
3. Touch the keypad icon next to the blue box in the “Password” field to open the on-screen keypad.	11
4. Enter a new 6-digit password and press the Enter (arrow) button. The \	11
Controls and Indicators	12
Button Operation	12
1. open	12
2. DISP/TILT	12
3. AS/PS	12
4. BAND/LOC/DX	12
5. AUdio	12
6. SRC	12
7. WIDE/PIC	12
8. MUTE	12
9. IR Remote Control Receiver	12
10. (left joystick)	12
MENU Mode: Press once to move the cursor to the left.	12
11. (down joystick)	12
12. Reset	12
Controls and Indicators	13
13.Pause/Play/Enter	13
15. (up joystick)	13
16. ()	13
17. TFT Display	13
18. REAR	13
19. RPT	13
20. PIP	13
21. SD Card Slot	13
Remote Control	14
Table 1: Remote Control Functions	15
Using the TFT Monitor	17
Open/Close TFT Monitor	17
Open TFT Monitor	17
Close TFT Monitor	17
Monitor Tilt Angle Adjustment	17
Step by Step Angle Adjustment	17
Continuous Angle Adjustment	17
Reverse Driving Use	17
Aspect Ratio	17
Image Setting	17
Table 2: Video Output Modes	17
Parameter Adjustment Procedure	17
1. Enter Picture Quality Setting Mode: Press the PIC button (24) on the remote control or press and hold the WIDE/Pic button (7) on the monitor.	17
2. Select Item to Set: Use the up/down joystick buttons to select “BRIGHT” or “CONTRAST”.	17
3. Set Parameters: Use the left/right joystick buttons to modify the settings.	17
4. Exit Picture Quality Setting Mode: Press the PIC button on the remote control or the WIDE/ Pic button on the monitor	17
Parking Brake	17
Parking Brake Inhibit	17
Parking Brake Sequence	17
a. Release parking brake for 3 ~ 5 seconds.	17
b. Reapply parking brake.	17
c. Video should be displayed on the TFT monitor within 1 ~ 2 seconds.	17
a. Set parking brake for 3 ~ 5 seconds.	17
b. Release parking brake for 3 ~ 5 seconds.	17
c. Reapply parking brake.	17
d. Video should be displayed on the TFT monitor within 1 ~ 2 seconds.	17
Operating Instructions	18
Power On / Off	18
Audible Beep Confirmation	18
Volume Adjustment	18
Programmable Turn-On Volume	18
Mute	18
Line Mute	18
Playing Source Selection	18
Auxiliary Devices	18
Source Menu	18
This menu allows you to select a source for the front or rear zone. Touch FRONT or REAR to choose the zone for which you would like to specify the source. (See “Multi-ZONE Operation” on page 16.)	18
Audio Control Menu	18
1. Use the left/right joystick buttons to highlight the audio feature to be adjusted.	19
2. Press the joystick Enter button on the control panel (13) or remote control (18) to select the highlighted option.	19
3. Use the joystick to adjust the selected feature to the desired setting.	19
Table 3: Audio Adjustments	19
Alternate Display Options	19
System Reset	19
Multi-ZONE Operation	20
Multi-Zone Limitations	20
Connecting the Rear Zone Touch Screen	20
Changing the Rear Zone Source	20
Controlling the Rear Zone Screen(s)	20
Turning the Rear Screen Off	20
Setup Menu	21
Accessing Menu Items	21
Adjusting a Feature	21
1. Use the touchscreen or press the /\\ or V buttons on the joystick to select the feature to be adjusted.	21
2. Enter the option field for the feature you want to adjust by using the touchscreen or pressing the Enter (joystick) button. A submenu appears in a second row with the selected option highlighted in blue.	21
3. Select a new value by using the touchscreen or pressing the /\\ or V buttons on the joystick.	21
4. Use the touchscreen or press the Enter (joystick) button to confirm setup.	21
General Sub-menu Features	21
Language Sub-menu Features	21
Audio Sub-menu Features	21
Speaker Sub-menu Features	21
Bluetooth Sub-menu Features	22
RDS Sub-menu Features	22
Rating Sub-menu Features	22
DivX Sub-Menu Features	22
Hardware Sub-menu Features	22
P.VOL Sub-menu Features	23
TS Cal (Screen Calibration)	23
Exiting the System Setup Menu	23
Tuner Operation	24
Tuner TFT Display	24
1. Current radio band indicator	24
2. Radio frequency indicator	24
3. Clock	24
4. Stereo broadcasting indicator	24
5. Strong Local signal broadcasting indicator	24
6. Preset radio stations: Touch to recall preset stations	24
7. RDS Information: PS (Program Service), PTY (Program Type), RT (Radio Text)	24
8. EQ: Touch to view Spectrum Analyzer > Equalizer	24
9. Touch to access the direct entry screen	24
10. Current preset station indicator	24
11. \|<<: Touch to seek backward	24
12. >>\|: Touch to seek forward	24
13. : Touch to tune backward one step	24
14. : Touch to tune forward one step	24
15. BAND: Touch to change between AM/FM bands	24
16. AS: Touch to automatically store stations	24
17. Touch to view the SOURCE MENU and select a new playback source	24
18. MEM: View screen used to enter current channel into preset memory	24
19. 1/2 or 2/2: Touch this page button to view a second page of on-screen buttons	24
20. Touch to view the SETUP menu	24
21. PS (Preview Scan): Touch to scan all stations available, stopping for 5 seconds at each and continuing until a station is selected	24
22. LOC: Touch to tune to strong local stations	24
23. PTY: When PTY is pressed, the Program Type categories are listed, allowing listeners to find similar programming by genre. When a PTY category is selected from the touch screen menu, the radio will start scanning for the selected category.	24
24. Indicates the PTY function is activated	24
25. Indicates the RDS function is activated	24
26. REAR: Touch to view the Rear source screen	24
27. PIP: Touch to view Rear, Front or NAV source	24
Switch to Radio Tuner source	24
Select FM/AM Band	24
Seek Tuning	24
Manual Tuning	24
Direct Tuning	24
Using Preset Stations	24
Storing a Station	24
1. Select a band (if needed), then select a station.	24
2. Touch the on-screen MEM button (18), on page 2/2 of the onscreen options, to open the preset screen.	24
3. Touch the preset number in which you would like to store the current station (or press EXIT to cancel and close the menu). The preset number and station appears highlighted.	24
Recalling a Station	25
1. Select a band (if needed).	25
2. Touch an on-screen preset button (6) to select the corresponding stored station.	25
Auto Store (AS/PS)	25
1. Select a band (if needed).	25
2. Press the AS/PS button (3) on the control panel or touch AS on the screen for 2 seconds to activate the Auto Store function.	25
Preview Scan (PS)	25
Local Radio Station Seeking (LOC)	25
Satellite Radio Operation	26
Accessing Satellite Radio Mode	26
1. SAT channel name	26
2. SAT channel number	26
3. SAT band	26
4. Time	26
5. Song title	26
6. Artist name	26
7. Song category	26
8. Signal strength indicator	26
9. Current preset channels/on-screen preset buttons	26
10. CH -: Select the previous channel	26
11. CH +: Select the next channel	26
12. CAT +: Select next channel in current category only	26
13. CAT -: Select previous channel in current category only	26
14. Touch to enter channel directly using keypad on screen	26
15. CG: Access Channel/Category Guide mode	26
16. BAND: Change between SAT1, SAT2 and SAT3 bands	26
17. Touch to view the SETUP menu	26
18. Touch this area to view the SOURCE MENU and select a new playback source	26
19. MEM: View screen used to enter current channel into preset memory	26
20. DIAG: This feature is reserved for use by service professionals for troubleshooting.	26
Displaying the Identification (ID) Code	26
Selecting a Station	26
Preset Mode	26
Storing a Station	26
1. Select a band (if needed), then select a station.	26
2. Touch the on-screen MEM button (18) to open the preset screen.	26
3. Touch the preset number in which you would like to store the current station (or press EXIT to cancel and close the menu). The preset number and station appears highlighted.	26
Recalling a Station	26
1. Select a band (if needed).	26
2. Touch an on-screen preset button to select the corresponding stored station.	26
Direct Tuning	26
Channel/Category Guide Mode	26
Channel Guide Mode	26
Category Guide Mode	27
DVD/VCD Video Operation	28
Inserting a Disc	28
Ejecting a Disc	28
Reset the Loading Mechanism	28
Accessing DVD Mode	28
Controlling Playback	28
Stopping Playback	28
Pausing Playback	28
Fast Forward Playback	28
Fast Reverse Playback	28
Slow Forward/Slow Reverse Playback	28
Repeat Playback	28
Sectional Repeat Function (A-B)	28
Random Playback	28
Picture in Picture (PIP)	28
Accessing the DVD Menu	28
Moving Through Chapters	29
Direct Chapter / Track Selection	29
Remote Control Direct Entry	29
Touch Screen Direct Entry	29
Viewing an Alternate Picture Angle (DVD Only)	29
Zooming	29
Multi-Language Discs (DVD Only)	29
Changing Audio Language	29
Changing Subtitle Language	29
PBC (Play Back Control - VCD Only)	29
Playback Information	29
DVD Playback Information	29
VCD Playback Information	29
General Disc Information	30
Table 4: Disc Properties	30
Table 5: Disc Symbols	30
DVD/CD Audio Operation	31
CD Player User Interface	31
1. Current track and total number of tracks on disc	31
2. Elapsed playing time/length of track	31
3. Current track title	31
4. Available track titles	31
5. ID3 information	31
6. \|\|: Touch to pause/play disc playback	31
7. : Touch to stop disc playback	31
8. >>\|: Touch to move to next track	31
9. \|<<: Touch to move to previous track	31
10. />>: Touch to navigate playlist/touch to fast forward	31
11. /<<: Touch to navigate playlist/touch to fast rewind or reverse	31
12. Touch to activate/deactivate Repeat play mode	31
13. 1/2 or 2/2: Touch this page button to view a second page of on-screen buttons	31
14. Touch to access the direct entry screen	31
15. Touch to view the SETUP menu	31
16. Touch to view Spectrum Analyzer > Equalizer	31
17. Touch to view the SOURCE MENU and select a new playback source	31
18. Touch the scroll bar and arrows to view the previous/ next page of songs	31
19. Touch to access the Music menu	31
20. Touch to access the Video menu	31
21. Touch to access the Photo menu	31
22. Browse all files	31
23. DIR -: Touch to view the previous folder	31
24. DIR +: Touch to view the next folder	31
25. Current time	31
Controlling Playback	31
Stopping Playback	31
Pausing Playback	31
Moving Through Tracks	31
Repeat Playback	31
Track Scan Select (CD-DA discs only)	31
Random Play Select	31
Fast Forward	31
Fast Reverse	31
Direct Track Entry	32
MP3/WMA Operation	33
MP3/WMA Media and File Requirements	33
MP3 Format Compatibility	33
MP3 Playing Order	33
Loading an SD Card	33
Loading a USB Device	33
1. Locate the USB jack located on the MediaLink4.	33
2. Insert the USB device into the USB connector. The unit will read the audio media files on the USB device automatically.	33
MP3 User Interface	34
1. Current track and total number of tracks on root of disc	34
2. Elapsed playing time, track length	34
3. Current time	34
4. Track titles	34
5. ID3 information	34
6. \|\| : Touch to play/pause disc playback	34
7. : Touch to stop disc playback	34
8. >>\|: Touch to move to next track	34
9. \|<<: Touch to move to previous track	34
10. />>: Touch to navigate playlist/touch to fast forward	34
11. /<<: Touch to navigate playlist/touch to fast rewind or reverse	34
12. DIR -: Touch to view the previous folder	34
13. DIR +: Touch to view the next folder	34
14. Touch to access the direct entry screen	34
15. Touch to view the SETUP menu	34
16. Touch to view Spectrum Analyzer > Equalizer	34
17. Touch to view the SOURCE MENU and select a new playback source	34
18. Folder name	34
19. 1/2 or 2/2: Touch this page button to view a second page of on-screen buttons	34
20. Touch the scroll bar and arrows to view the previous/ next page of songs	34
21. Touch to activate/deactivate Repeat play mode	34
22. Touch to access the Music menu	34
23. Touch to access the Video menu	34
24. Touch to access the Photo menu	34
25. Browse all files	34
Controlling MP3/WMA Disc Playback	34
Playing MP3/WMA Files	34
Stopping Playback	34
Pausing Playback	34
Moving Through Tracks	34
Repeat Playback	34
Random Play Select	34
iPod Operation	35
iPod User Interface	35
1. Elapsed playing time	35
2. Current track and total number of files	35
3. Current time	35
4. Media titles/menu information	35
5. ID3 information	35
6. Enter	35
7. Touch to access photos	35
8. >>\|: Touch to move to next track	35
9. \|<<: Touch to move to previous track	35
10. Touch to access the iPod menu	35
11. >\|\| : Touch to play/pause disc playback	35
12. Touch to access music files	35
13. Touch to access video files	35
14. Touch to access the SETUP screen	35
15. Touch to view Spectrum Analyzer > Equalizer	35
16. Touch to view the SOURCE MENU and select a new playback source	35
17. Song title	35
18. Touch to view the direct entry menu	35
19. Touch the scroll bar and arrows to view the previous/ next page of songs	35
Controlling Your iPod	35
Fast Forward/Fast Reverse	35
Photo Playback	35
Video Playback	35
Direct Track/File Entry	35
Bluetooth Operation	36
About Bluetooth	36
Bluetooth User Interface	36
1. Current connection status/device connected	36
2. Current time	36
3. Bluetooth menu	36
4. Current operation status	36
5. Toggle Music/Phone menu	36
6. Transfer active call back to handset	36
7. Pair your Bluetooth phone (first time use)	36
8. Connect/disconnect Bluetooth device (phone, PDA, personal music player, etc.) with hand-free function	36
9. Exit call listing display	36
10. Mute/unmute microphone (located on left side of radio) during active call	36
11. Answer incoming call/make call	36
12. Reject incoming call/end call/quit pairing process/quit reading phone book or call listing	36
13. Touch to view the SETUP menu	36
14. Touch to view Spectrum Analyzer > Equalizer	36
15. Touch to view the SOURCE MENU and select a new playback source	36
16. Indicates connection/current operation (--> indicates incoming call, <-- indicates dialing alert)	36
17. Touch to access the direct entry screen	36
18. : Touch to stop playback	36
19. Touch the scroll bar and arrows to view the previous/ next page of songs	36
20. Toggle Music/Phone menu/mode	36
21. Play/Pause selected file	36
22. \|<<: Touch to move to the previous file	36
23. >>\|: Touch to move to the next file	36
24. Signal strength indicator	36
Hands Free Profile (HFP)	36
Pairing the Bluetooth System with Your Mobile Phone and Head Unit	37
1. Press the button (8) to initiate the pairing process. Keep the mobile phone within 2 meters of the head unit when pairing. (To terminate the pairing process, press the button again.)	37
2. Select the Bluetooth setup option on the mobile phone to be paired (please refer to the phone’s instruction manual to learn how to enter Bluetooth setup, turn Bluetooth on/off, and perform pairing).	37
3. Select “VM9022” from the pairing list on the mobile phone.	37
Reconnecting	37
Managing Incoming Calls	37
Answering an Incoming Call	37
Rejecting an Incoming Call	37
Volume Control	37
Microphone Mute	37
Making an Outgoing Call	37
1. Touch the button to open the direct dial screen.	37
2. Use the 0-9, *, and # buttons to input the phone number.	37
3. After entering the phone number, press the button to dial the call. The direct dial screen will close once your call is connected.	37
Call Transfer	37
Menu List	37
Missed Calls	37
Dialed Calls	37
Received Calls	37
Phone Book	37
1. Touch the Phone Book menu option to display the phone book stored on your mobile phone, if compatible. The screen will display “Ready...” while the phone book is downloading.	37
2. Once the download is completed, you can use the arrow buttons and scroll bar on the right side of the window to navigate the ...	37
3. Touch to highlight the number you want to dial and then touch the button.	38
Bluetooth Setup	38
Auto Answer	38
1. Touch the button to view the SETUP menu.	38
2. Select the “Bluetooth” sub-menu.	38
3. Touch the area to the right of “Auto answer” to select “On”.	38
Auto Connect	38
1. Touch the button to view the SETUP menu.	38
2. Select the “Bluetooth” sub-menu.	38
3. Touch the area to the right of “Connect” to select “Auto”.	38
Advanced Audio Distribution Profile (A2DP)	38
Troubleshooting	39
Table 6: Troubleshooting	39
Error Messages	40
Table 7: Error Messages	40
Care and Maintenance	41
1. Use only a clean silicone cloth and neutral detergent to clean the front panel or monitor. A rough cloth and non- neutral detergent (such as alcohol) may result in scratching or discoloration.	41
2. Do not get water or cleaning fluids on the unit.	41
3. If the temperature inside the player gets too hot, a protective circuit automatically stops play of the disc. If this occurs, allow the unit to cool before operating the player again.	41
4. Never insert anything other than a 5” (12 cm) disc into the player as the mechanism can be damaged by foreign objects.	41
5. Do not attempt to use a 3” (8 cm) CD-Single disc in this unit, either with or without an adaptor, as damage to the player and/or disc may occur. Such damage is not covered by the Warranty on this product.	41
6. The CD player may not operate properly in extreme hot or cold. If such conditions occur, allow the interior of the vehicle to reach a normal temperature before using player.	41
7. When the vehicle warms up during cold weather or under damp conditions, condensation may appear on the screen. Should this occur, the screen will not operate properly until the moisture has evaporated.	41
8. We suggest you use a cleaning disc in this unit more frequently than in the unit in your home due to the environmental conditions of the vehicle.	41
Specifications	42
DVD/CD Player	42
Video	42
FM Tuner	42
AM Tuner	42
Monitor	42
General	42