Jensen VM9423 Operation Manual - Page 11
Open/Close TFT Monitor, Monitor Tilt Angle Adjustment, Aspect Ratio, Image Setting, Parking Brake
UPC - 043258304438
View all Jensen VM9423 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 11 highlights
VM9423 USING THE TFT MONITOR Open/Close TFT Monitor Open TFT Monitor Press the OPEN/CLOSE button (1) on the front panel or press the ( ) button (25) on the remote control to slide the monitor down and reveal the disc and SD card slots. Close TFT Monitor Press the OPEN/CLOSE button (1) on the front panel or press the ( ) button (25) on the remote control close the monitor panel. Monitor Tilt Angle Adjustment A known characteristic of LCD panels is the quality of the display in relationship to the viewing angle. The monitor angle can be adjusted for optimum viewing using one of the following methods. Step by Step Angle Adjustment Press the ( ) or ( ) button on the remote control (26, 27) to adjust the tilt angle of the screen one step at a time. You can also adjust the tilt by pressing and holding the OPEN button (1) on the front panel. Use the up/down joystick buttons to adjust the angle of the screen while the red tilt icon is flashing. Continuous Angle Adjustment Press and hold the ( ) or ( ) button on the remote control to adjust the tilt angle in a continuous motion. Reverse Driving Use If the rear-view video camera is connected, the unit is on, and the monitor is stationed inside the main compartment of the unit, the monitor automatically moves into the viewing position and switches to CAMERA mode upon reverse driving. When the reverse driving stops, the monitor returns to the main storage compartment. If the monitor is in display mode, the monitor automatically switches to CAMERA mode upon reverse driving. When the reverse driving stops, the monitor returns to its original input mode. Aspect Ratio Press the WIDE button (28) on the remote control or WIDE button (22) on the monitor to adjust the aspect ratio as follows (only active with video source): CINEMA The entire screen is extended horizontally to the aspect ratio of 16 to 9. The extension ratio is the same at any point. NORMAL The conventional display image has a 4 to 3 ratio of horizontal to vertical, leaving a blank area on the right and left sides of the display. STANDBY Screen becomes black. Touch screen to resume. Image Setting Table 2 shows the video output mode for each playing source. Table 2: Video Output Modes Playing Source Video Output Modes RADIO RGB Mode SAT RGB Mode DISC RGB Mode BT RGB Mode AUX 1 CVBS Mode AUX 2 CVBS Mode NAV RGB Mode CAMERA CVBS Mode *CVBS - Composite Video Baseband Signal Parameter Adjustment Procedure 1. Enter Picture Quality Setting Mode: Press the PIC button on the remote control or monitor. 2. Select Item to Set: Use the up/down joystick buttons to select "BRIGHT" or "CONTRAST". 3. Set Parameters: Use the left/right joystick buttons to modify the settings. 4. Exit Picture Quality Setting Mode: Press the PIC button on the remote control or monitor. Parking Brake Inhibit When the pink "Parking" wire is connected to the vehicle Parking Brake circuit, the front TFT monitor will display video when the Parking Brake is engaged. (When the pink wire is grounded via the Parking Brake circuit, video will be displayed.) Monitor Movement Mechanism If an obstruction occurs in the monitor path, the following protective measurements can be executed to prevent damage to the mechanism or monitor: Table 3: Monitor Protective Measures Obstruction Self Protection Monitor loading out horizontally Monitor loading in horizontally Monitor loading out vertically Monitor loading in vertically Unit stops at obstruction point Unit stops at obstruction point Unit stops at obstruction point Unit stops at obstruction point OPEN Button Power Pressed Reconnected Monitor fully extended horizontally Monitor fully extended horizontally Monitor swivels back to the unit Monitor swivels back to the unit Monitor is automatically loaded into unit Monitor is automatically loaded into unit Monitor swivels back to the unit Monitor swivels back to the unit After the protective procedure is executed, normal operation is resumed by pressing the OPEN button (1) or disconnecting and reconnecting the power. 7