Karcher EDI 4 Operating instructions 1 - Page 14

Initial startup, Operation, Storage

Get Karcher EDI 4 PDF manuals and user guides View all Karcher EDI 4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Blink codes ● LED lights up permanently: The device is in operation. ● LED lights up for 1 h: The device is connected to the power supply and the battery is fully charged. ● During operation: Low battery voltage warning. ● The battery is discharged. ● During charging: Battery is being charged. A fault has occurred (see Chapter Troubleshooting guide). Initial startup Battery charging 1. Charge the battery. Illustration B Note The charge indicator flashes during the charging procedure. It lights up continuously for 1 hour when the battery is fully charged. For information on the charging time, see Chapter Technical data. Operation General information on handling the device  Clean the device each time before use (see Chapter Cleaning the device).  Regularly clear the car windows of dirt to remove dirt particles that could cause scratches. Notice that the greatest contamination is outside the wiping area of the windscreen wipers. That is why it is not enough to clean the car windows with the windscreen washer system alone. Illustration C  When scraping ice on an uncleaned windshield, limit it to the wiping area of the windscreen washer system in order to avoid possible scratches due to dirt from the edge areas.  Guide the device slowly over the surface while pressing lightly.  At regions with thicker ice, leave the device at the same position until the ice breaks. Note Extra de-icing agents are not required. Starting up the device 1. Press the power switch. Illustration D The device is switched on and is in standby mode. 2. Pull off the protective cap by pressing at the side. Illustration E 3. Position the device on the windscreen. Take care to ensure adequate clearance to seals and paintwork. Illustration F 4. Actuate the trigger switch. Illustration G The scraper disc starts rotating. Storage ATTENTION Improper storage Damage to the device and battery Do not store the device in a vehicle for longer periods of time. 14 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
14
English
Blink codes
Initial startup
Battery charging
1.
Charge the battery.
Illustration B
Note
The charge indicator flashes during the charging procedure.
It lights up continuously for 1 hour when the battery is fully
charged. For information on the charging time, see Chapter
Technical data.
Operation
General information on handling the device
Clean the device each time before use (see Chapter
Cleaning the device
).
Regularly clear the car windows of dirt to remove dirt par-
ticles that could cause scratches. Notice that the greatest
contamination is outside the wiping area of the wind-
screen wipers. That is why it is not enough to clean the car
windows with the windscreen washer system alone.
Illustration C
When scraping ice on an uncleaned windshield, limit it to
the wiping area of the windscreen washer system in order
to avoid possible scratches due to dirt from the edge are-
as.
Guide the device slowly over the surface while pressing
lightly.
At regions with thicker ice, leave the device at the same
position until the ice breaks.
Note
Extra de-icing agents are not required.
Starting up the device
1.
Press the power switch.
Illustration D
The device is switched on and is in standby mode.
2.
Pull off the protective cap by pressing at the side.
Illustration E
3.
Position the device on the windscreen. Take care to en-
sure adequate clearance to seals and paintwork.
Illustration F
4.
Actuate the trigger switch.
Illustration G
The scraper disc starts rotating.
Storage
ATTENTION
Improper storage
Damage to the device and battery
Do not store the device in a vehicle for longer periods of time.
●
LED lights up permanently:
The device is in operation.
●
LED lights up for 1 h: The
device is connected to the
power supply and the battery
is fully charged.
●
During operation: Low
battery voltage warning.
●
The battery is discharged.
●
During charging: Battery is
being charged.
A fault has occurred (see Chap-
ter
Troubleshooting guide
).