Kenmore 7808 Use and Care Guide - Page 5

Parts needed Check local codes and with gas supplier. Check existing gas supply, electrical supply and venting. Read "Electrical Requirements," "Gas Supply Requirements" and "Venting Requirements" before purchasing parts. Mobile home installations require special parts (listed following) available for purchase from your local Sears store or Sears Service Center. For further information, please call 1-800-4-MY-HOME _ (1-800-469-4663). • Mobile Home Installation Kit. Ask for Part Number 346764. • Metal exhaust system hardware. 56.5 cm) Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Place dryer at least 18 inches (46 cm) above the floor for a garage installation. Failure to do so can result in death, explosion, or fire. You will need • A location that allows for proper exhaust installation. A gas dryer must be exhausted to the outdoors. See "Venting Requirements." • A grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See "Electrical Requirements." • A sturdy floor to support the total weight (dryer and load) of 200 Ibs (90.7 kg). The combined weight of a companion appliance should also be considered. • Cold water faucets located within 4 ft (1.2 m) of the water fill valves, and water pressure of 20-100 psi (138-690 kPa). You may use the water supply for your washer using the "Y" connector and short hose (if needed) which are provided. • 20-100 psi (138-690 kPa) for best performance. • A level floor with a maximum slope of 1" (2.5 cm) under entire dryer. Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. Drying times can be extended. The dryer must not be installed or stored in an area where it will be exposed to water and/or weather. Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector. NOTE: No other fuel-burning appliance can be installed in the same closet as a dryer. Installation Clearances The location must be large enough to allow the dryer door to open fully. *Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the exhaust vent with elbow. See "Venting Requirements." Installation spacing for recessed area or closet installation The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of O" (0 cm) clearance on the sides and rear. Recommended spacing should be considered for the following reasons: • Additional spacing should be considered for ease of installation and servicing. • Additional clearances might be required for wall, door and floor moldings. • Additional spacing should be considered on all sides of the dryer to reduce noise transfer. For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable. • Companion appliance spacing should also be considered. • Additional spacing is required if you exhaust out the rear of the dryer to either the right or left side. 3.* m ¢6cm) 18,,.3C (45.c7m) Z 14m,, a_, 4_in2_j 1"_ _ 2m'__fl _1 _ ÷11"_12__'__ s_' (25cm) (73.7cm) (2.5crn) (2.5cm) (7&3cm)(12.7crn) A B C A. Recessed area B. Side view - closet or confined area C. Closet door with vents _ 3,,, lT.6cm) *Required spacing Mobile Home - Additional Installation Requirements This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). Mobile home installations require: • Metal exhaust system hardware, which is available for purchase from your local Sears store or Sears Service dealer.