Kenmore 8787 Use and Care Guide - Page 13

Optional 3-wire connection

Get Kenmore 8787 - Elite HE3 7.0 cu. Ft. Electric Dryer PDF manuals and user guides View all Kenmore 8787 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown. 1= Loosen or remove center silver-colored terminal block screw. 2. Place the hooked end of the neutral wire (white or center wire) of direct wire cable under the center screw of terminal block (hook facing right). Squeeze hooked end together. Tighten screw. Optional 3-wire connection Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire. 1. Remove center silver-colored terminal block screw. 2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord/cable under center, silver-colored terminal block screw. Tighten screw. D A. External ground conductor screw B.Neutral ground wire C. Center silver-colored terminal block screw D. Neutral wire (white or center wire) EL_" (1.9 cm) UL Iisted strain relief Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws. !! !! A. External ground conductor screw B. Center silver-colored terminal block screw C. Neutral ground wire D. Neutral wire (white or center wire) EL _" (!.9 cm) UL ilsted strain relief F Grounding path determined by a qualified electrician Connect the other wires to outer terminal block screws. Tighten screws. !! !! ----= 4. Tighten strain relief screw. 5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 6. You have completed your electrical connection. Now go to "Venting Requirements." 4= Tighten strain relief screws. 5. Connect a separate copper ground wire from the external ground conductor screw to an adequate ground. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
When connecting
to the terminal
block,
place the hooked
end of
the wire under the screw of the terminal
block (hook facing right),
squeeze hooked
end together
and tighten
screw,
as shown.
1=
2.
Loosen or remove center silver-colored
terminal
block screw.
Place the hooked
end of the neutral wire (white or center wire)
of direct wire cable under the center screw of terminal
block
(hook facing
right). Squeeze
hooked end together. Tighten
screw.
Optional 3-wire connection
Use for direct wire or power supply cord where
local codes
do not permit connecting
cabinet-ground
conductor
to
neutral wire.
1.
Remove
center silver-colored
terminal
block screw.
2.
Remove
neutral ground wire from external
ground
conductor
screw. Connect
neutral ground
wire and the neutral wire
(white or center wire) of power supply
cord/cable
under
center, silver-colored
terminal
block screw. Tighten
screw.
D
A. External ground conductor screw
B.Neutral ground wire
C. Center silver-colored terminal block screw
D. Neutral wire (white or center wire)
EL
_"
(1.9 cm) UL Iisted strain relief
Place the hooked ends of the other direct wire cable wires
under the outer terminal
block screws
(hooks facing right).
Squeeze
hooked ends together. Tighten
screws.
!!
!!
4.
Tighten strain relief screw.
5.
Insert tab of terminal
block cover into slot of dryer rear panel.
Secure cover with
hold-down
screw.
6.
You have completed
your electrical
connection.
Now go to
"Venting
Requirements."
4=
5.
A. External ground
conductor
screw
B. Center
silver-colored
terminal
block screw
C. Neutral
ground
wire
D. Neutral
wire (white or center
wire)
EL
_"
(!.9
cm) UL
ilsted
strain relief
F
Grounding
path determined
by a qualified
electrician
Connect
the other wires to outer terminal
block screws.
Tighten screws.
!!
!!
----=
Tighten strain relief screws.
Connect
a separate
copper
ground
wire from the external
ground
conductor
screw
to an adequate
ground.
Insert tab of terminal
block cover into slot of dryer rear panel.
Secure cover with hold-down
screw.
13