Kenwood 3025 Instruction Manual - Page 25

Screwing the Faceplate on the Unit, English, If you want to fasten the faceplate to the main

Get Kenwood 3025 - High Power SIRIUS Ready CD Receiver PDF manuals and user guides
UPC - 019048150097
View all Kenwood 3025 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off. 1 Refer to the section 'Removing the hard rubber frame' (page 26) and then remove the hard rubber frame. 2 Drop open the faceplate by pressing the Release button. 3 Tighten the screws (ø2.6 × 12 mm) (Accessory 5) in the holes shown on the diagram. Accessory5 4 Tighten the screws (ø2 × 4 mm) (Accessory 6) in the holes shown on the diagram. Accessory6 5 Tighten the screws (ø2 × 6 mm) (Accessory 7) in the holes shown on the diagram. Accessory7 • Never insert the screws in any other screw hole than the one specified. If you screw them in another hole, it will contact and may cause damage to the mechanical parts inside the unit. English | 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
English
|
25
Screwing the Faceplate on the Unit
If you want to fasten the faceplate to the main
unit so that it does not fall off.
1
Refer to the section 'Removing the hard rubber
frame' (page 26) and then remove the hard
rubber frame.
2
Drop open the faceplate by pressing the Release
button.
3
Tighten the screws (ø2.6 × 12 mm) (Accessory
5
) in the holes shown on the diagram.
Accessory
5
4
Tighten the screws (ø2 × 4 mm) (Accessory
6
) in
the holes shown on the diagram.
Accessory
6
5
Tighten the screws (ø2 × 6 mm) (Accessory
7
) in
the holes shown on the diagram.
Accessory
7
• Never insert the screws in any other screw hole than the
one specified. If you screw them in another hole, it will
contact and may cause damage to the mechanical parts
inside the unit.