Kenwood DNX5250BT Quick Start Guide - Page 29

Accessory

Get Kenwood DNX5250BT PDF manuals and user guides View all Kenwood DNX5250BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

ÑÑConnecting wires to terminals DAB antenna CX-DAB1 (Optional accessory) (DNX7250DAB, DNX525DAB, DNX4250DAB only) Fuse (10A) Fuse (10A) Use of a CX-DAB1(optional accessory) as a DAB antenna is recommended. When using a commercially available DAB antenna, the diameter of the SMB connector must be Φ6.5 mm or less. Φ 6.5 mm (maximum) A: Black (Ground wire) B: Yellow (Battery wire) C: Red (Ignition wire) Accessory 1 CB A Connector A Connector B 8642 7531 8642 7531 If no connections are made, do not let the wire come out from the tab. Connect either to the power control terminal when using the optional power amplifier, or to the power terminal for the booster amplifier of the film-type or short pole type antenna. Connect to the terminal that is grounded when either the telephone rings or during conversation. To use the steering wheel remote control feature, an exclusive remote adapter (not supplied) that matches your car is required. Blue/White (Power control/ Antenna control wire) P.CONT ANT. CONT Brown (Mute control wire) MUTE Light Blue/Yellow (Steering remote control wire) REMOTE CONT STEERING WHEEL REMOTE INPUT 2 WARNING for Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in (1) below. If the ISO connector pins are set as described in (2), make the connection as illustrated. Please be sure to reconnect the cable as shown (2) below to install this unit to the Volkswagen vehicles etc. (1): Default setting The red (A-7 pin) of the vehicle's ISO connector is linked with the ignition, and the yellow (A-4 pin) is connected to the constant power supply. (2) The red (A-7 pin) of the vehicle's ISO connector is connected to the constant power supply, and the yellow (A-4 pin) is linked to the ignition. Red (Ignition cable) Red (A-7 pin) Red (Ignition cable) Red (A-7 pin) Unit Vehicle Unit Vehicle Yellow (Battery cable) Yellow (A-4 pin) Yellow (Battery cable) Yellow (A-4 pin) English ñ 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
English
ñ
29
Ñ
Connecting wires to terminals
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
P.CONT
ANT.
CONT
MUTE
REMOTE CONT
REMOTE INPUT
STEERING WHEEL
Fuse (10A)
Fuse (10A)
Accessory
1
A
B
C
A
: Black (Ground wire)
B
: Yellow (Battery wire)
C
: Red (Ignition wire)
Connector
A
Connector
B
2
WARNING for Connecting the ISO Connector
The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper
connections to prevent damage to the unit. The default connection for the wiring harness is described in (1) below. If
the ISO connector pins are set as described in (2), make the connection as illustrated. Please be sure to reconnect the
cable as shown (2) below to install this unit to the
Volkswagen
vehicles etc.
(2)
The red (A-7 pin) of the vehicle’s ISO connector is
connected to the constant power supply, and the
yellow (A-4 pin) is linked to the ignition.
(1): Default setting
The red (A-7 pin) of the vehicle’s ISO connector is linked
with the ignition, and the yellow (A-4 pin) is connected
to the constant power supply.
Red (Ignition cable)
Unit
Vehicle
Yellow (Battery cable)
Yellow (A-4 pin)
Red (A-7 pin)
Red (Ignition cable)
Unit
Vehicle
Yellow (Battery cable)
Yellow (A-4 pin)
Red (A-7 pin)
Connect either to the power control terminal when using the optional
power amplifier, or to the power terminal for the booster amplifier of
the film-type or short pole type antenna.
If no connections are made, do not let the
wire come out from the tab.
Connect to the terminal that is grounded when either the telephone
rings or during conversation.
To use the steering wheel remote control feature, an exclusive remote
adapter (not supplied) that matches your car is required.
Blue/White (Power control/
Antenna control wire)
Brown (Mute control wire)
Light Blue/Yellow (Steering remote
control wire)
DAB antenna CX-DAB1 (Optional accessory)
(DNX7250DAB, DNX525DAB, DNX4250DAB only)
Use of a CX-DAB1(optional accessory) as a DAB
antenna is recommended.
When using a commercially available DAB
antenna, the diameter of the SMB connector
must be Φ6.5 mm or less.
Φ 6.5 mm
(maximum)