Kenwood DPX-U5120 User Manual - Page 38

X'Over Setting, Car Type Fine Adjustments

Get Kenwood DPX-U5120 PDF manuals and user guides View all Kenwood DPX-U5120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Function of DPX-U6120 DSP Setup Car Type Fine Adjustments Adjusting fine tuning of the speaker position compensation value specified at (page 37). Display "FRONT" "REAR" "SW" Item Front speaker Rear speaker Subwoofer Range 0 - 440 cm 0 - 440 cm 0 - 440 cm ( : Factory setting) 1 Select the source Press the [SRC] button. Select a source other than "STDBY". 2 Enter Function setting mode Press the [VOL] knob. 3 Enter Car Type Adjustment mode Turn the [VOL] knob and press it when the desired item is displayed. Select "Audio Control" > "Detailed Setup" > "Car Type Adjust". 4 Select the item you want to set Operation type Selects the item. Adjust each item. Set the value Operation Turn the [VOL] knob. Press the [4] or [¢] button. Press the [VOL] knob. The settings of the delay time are automatically identified and compensated by specifying the distances of each speaker from the center of the vehicle interior. 1 Set the front and rear positions and the height of the reference point to the position of the ears of the person sitting in the front seat, and set the right and left positions to the center of the vehicle interior. 2 Measure the distances from the reference point to the speakers. 3 Calculate the distance difference in accordance with the farthest speaker. 38 | DPX-U6120/ DPX-U5120/ DPX-MP3120 Reference point FRONT DN DN FRONT REAR DN REAR DN DN DN SUB-W 5 Exit Function setting mode Press the [ ] button for at least 1 second. X'Over Setting Fine adjusting the following setting values corresponding to the X'Over values set in the section (page 37). Display Item "X'Over" "Front" "FC" "SLOPE" "Rear" "FC" "SLOPE" "SubWoofer" "FC" "SLOPE" "PHASE" Range Front High Pass Filter Through, 30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250 (Hz) Front High Pass Slope -6, -12, -18, -24 dB/Oct Rear High Pass Filter Through, 30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250 (Hz) Rear High Pass Slope -6, -12, -18, -24 dB/Oct Subwoofer Low Pass Filter 30, 40, 50, 60, 70, 80, 90, 100, 120, 150, 180, 220, 250, Through (Hz) Subwoofer Slope -6, -12, -18, -24 dB/Oct Subwoofer Phase Reverse (180°)/ Normal (0°) ( : Factory setting) 1 Select the source Press the [SRC] button. Select a source other than "STDBY". 2 Enter Function setting mode Press the [VOL] knob. 3 Enter X'Over setting mode Turn the [VOL] knob and press it when the desired item is displayed.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
38
|
DPX-U6120/ DPX-U5120/ DPX-MP3120
Reference point
FRONT
FRONT
SUB-W
REAR
REAR
50cm
80cm
150cm
+70cm
+0cm
+100cm
5
Exit Function setting mode
Press the [
] button for at least 1 second.
X’Over Setting
Fine adjusting the following setting values
corresponding to the X’Over values set in the
section <Speaker Setting> (page 37).
Display
Item
Range
“X’Over”
“Front”
“FC”
Front High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE”
Front High Pass Slope
-6,
-12, -18, -24 dB/Oct
“Rear”
“FC”
Rear High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE”
Rear High Pass Slope
-6,
-12, -18, -24 dB/Oct
“SubWoofer”
“FC”
Subwoofer Low Pass Filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250, Through (Hz)
“SLOPE”
Subwoofer Slope
-6,
-12, -18, -24 dB/Oct
“PHASE”
Subwoofer Phase
Reverse (180°)/ Normal (0°)
(
: Factory setting)
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
2
Enter Function setting mode
Press the [VOL] knob.
3
Enter X’Over setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Car Type Fine Adjustments
Adjusting fine tuning of the speaker position
compensation value specified at <Car Type
Selection> (page 37).
Display
Item
Range
“FRONT”
Front speaker
0 – 440 cm
“REAR”
Rear speaker
0 – 440 cm
“SW”
Subwoofer
0 – 440 cm
(
: Factory setting)
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
2
Enter Function setting mode
Press the [VOL] knob.
3
Enter Car Type Adjustment mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control”
>
“Detailed Setup”
>
“Car Type Adjust”.
4
Select the item you want to set
Operation type
Operation
Selects the item.
Turn the [VOL] knob.
Adjust each item.
Press the [
4
] or [
¢
] button.
Set the value
Press the [VOL] knob.
The settings of the delay time are automatically
identified and compensated by specifying the
distances of each speaker from the center of the
vehicle interior.
1 Set the front and rear positions and the height
of the reference point to the position of the ears
of the person sitting in the front seat, and set
the right and left positions to the center of the
vehicle interior.
2 Measure the distances from the reference point
to the speakers.
3 Calculate the distance difference in accordance
with the farthest speaker.
DSP Setup
Function of DPX-U6120