Kenwood KAC-729S Instruction Manual - Page 2

Controls KAC-829 KAC-729S KAC-629S KAC-529S 40 25 POWER IN GND FUSE(40A) BATT. P.CON(REMOTE) BRIDGED LEFT RIGHT SPEAKER OUTPUT 1234 5 POWER AMPLIFIER POWER IN GND FUSE(25A) BATT. P.CON(REMOTE) BRIDGED LEFT RIGHT SPEAKER OUTPUT 1 234 5 POWER AMPLIFIER FILTER OFF LPF OPERATION STEREO MONO(Lch) 0.5 0.3 GND 1.0 MIN MAX INPUT SENSITIVITY(V) LINE IN L R 6 7 89 0 SPEAKER LEVEL INPUT LEFT RIGHT ! FILTER OFF HPF LPF OPERATION L+R STEREO MONO(Lch) 0.5 0.3 GND 1.0 MIN MAX INPUT SENSITIVITY(V) LINE IN L R 6 7 89 0 SPEAKER LEVEL INPUT LEFT RIGHT ! Operations of the following control and switches are required in accordance with the center unit and speakers connected with this unit. 1 Fuse 40 A × 1 : KAC-829/729S 25 A × 1 : KAC-629S 15 A × 1 : KAC-529S NOTE If you can't find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal 4 Power control (REMOTE) terminal 5 SPEAKER OUTPUT terminals • Stereo Connections: When you wish to use the unit as a stereo amplifier, stereo connections are used. • Bridged Connections: When you wish to use the unit as a high-output monaural amplifier, bridged connections are used. (Make connections to the LEFT channel (+) and the RIGHT channel (-) SPEAKER OUTPUT terminals.) 6 RCA cable ground lead terminal When using an RCA cable with a ground lead attached, connect the ground lead to this terminal. 2CAUTION Do not use this terminal for power source grounding. This unit will be damaged if the power source grounding wire is connected to this terminal. 7 FILTER switch These switches allow filtering of the speaker output signals. • HPF (High Pass Filter) position (KAC629S only) Only frequencies of 150 Hz or higher are output. (Frequencies below 150 Hz are cut.) • LPF (Low Pass Filter) position Only frequencies of 80 Hz or lower are output. (Frequencies above 80 Hz are cut.) The Lch and Rch will be mixed before output even if the operation switch is set to STEREO. • OFF position The original sound without filtering is output. 8 OPERATION switch This switch allows selection of the amplification method of input signals. KAC-829 KAC-729S KAC-529S KAC-629S 9 0.5 0.3 10 1.0 15 20 MIN MAX (W) INPUT SENSITIVITY(V) 25W or greater STEREO/BRIDGEABLE AMPLIFIER KAC-829 MAXIMUM POWER STEREO/BRIDGEABLE AMPLIFIER KAC-829 Power indicator KAC-729S KAC-629S KAC-529S • STEREO position The amplifier can be used as a stereo amplifier. • L+R position (KAC-629S only) The input left and right signals are combined before being amplified. Use this position when the unit is used for subwoofer speakers or the L+R (monaural) sound is required. • MONO (Lch) position Amplifies the signal input from the left side only. Set to this position and make bridged connections to use as a high-power monaural amplifier. (The input right signal is not output.) 9 INPUT SENSITIVITY control Set this control according to the pre-output level of the center unit connected with this unit, or to the maximum power output of the genuine-accessory car stereo. Use the diagram on the right as a guide. NOTE For the pre-output level or the maximum power output, refer to the "Specifications" in the instruction manual of the center unit. 0 LINE IN terminal ! Speaker level input terminals Power indicator When the power is turned on, the Power indicator lights. If the Power indicator does not light when the power is turned on, the protection function may be activated. Check whether there is any indication of trouble. ■ The protection function is activated in the following situations: This unit is equipped with a protection function for protecting this unit and your speakers from various accidents or problems that can occur. When the protection function is triggered, the Power indicator goes off and the amplifier stops operating. • When a speaker wire may be short-circuited. • When a speaker output contacts ground. • When the unit malfunctions and a DC signal is sent to the speaker output. • When the internal temperature is high and unit won't operate. • When a ground wire of the center unit (cassette receiver, CD receiver, etc.) or this unit is not connected to a metal part serving as an electrical ground passing electricity to the battery's negative - terminal. System examples ■ 2-channel system CENTER UNIT L L R R Left speaker Right speaker KAC-829/729S/529S 7 8 FILTER OPERATION OFF LPF STEREO MONO(Lch) KAC-629S 7 8 FILTER OPERATION OFF L+R HPF LPF STEREO MONO(Lch) ■ Subwoofer system CENTER UNIT L L R R Left speaker Right speaker Subwoofer KAC-829/729S/529S 7 8 FILTER OPERATION OFF LPF STEREO MONO(Lch) KAC-629S 7 8 FILTER OPERATION OFF L+R HPF LPF STEREO MONO(Lch) ■ 1-channel system CENTER UNIT L L L R R R L L R R Left speaker Right speaker KAC-829/729S/529S 7 8 FILTER OPERATION OFF LPF STEREO MONO(Lch) KAC-629S 7 8 FILTER OPERATION OFF L+R HPF LPF STEREO MONO(Lch) Connection *...Commercially available parts NOTE For safe installation, read "Installation procedure" before starting work. ■ RCA cable connection ■ Speaker level input connection CENTER UNIT (Cassette receiver, CD receiver, etc.) Genuine-accessory car stereo (No line output center unit etc.) Speaker RCA cable* Car fuse box 6 GND FILTER OFF LPF OPERATION STEREO MONO(Lch) 0.5 0.3 GND 1.0 MIN MAX INPUT SENSITIVITY(V) LINE IN L R SPEAKER LEVEL INPUT LEFT RIGHT Battery ! LEVEL RINIGHPTUT SPELEAFKT ER ACC FILTER OFF LPF OPERATION STEREO MONO(Lch) 0.5 0.3 GND 1.0 MIN MAX INPUT SENSITIVITY(V) LINE IN L R SPEAKER LEVEL INPUT LEFT RIGHT Power control wire* ■ Speaker stereo connection Lead terminal* 5BRIDGED LEFT RIGHT 4 POWER IN GND BATT. P.CON(REMOTE) BRIDGED LEFT RIGHT SPEAKER OUTPUT POWER AMPLIFIER ■ Speaker bridge connection Lead terminal* 5BRIDGED LEFT RIGHT 4 POWER IN GND BATT. P.CON(REMOTE) BRIDGED LEFT RIGHT SPEAKER OUTPUT POWER AMPLIFIER ■ Tri-mode CENTER UNIT High pass L L R R L Crossover Frequency C 0 dB Subwoofer (L + R) -3 dB C L C KAC-829/729S/529S 7 8 FILTER OPERATION OFF LPF STEREO MONO(Lch) KAC-629S 7 8 FILTER OPERATION OFF L+R HPF LPF STEREO MONO(Lch) Frequency C= 159000 fc x R (µF) = 159000 120Hz x 4Ω = 331.25 µF L= 159 x R fc (mH) = 159 x 4Ω 120Hz = 5.3 mH Principle of Tri-mode Method of frequency band division using a coil and capacitor ... in case of 6dB/oct. slope Coil (L): Passes low frequencies and blocks high frequencies. (Low pass) Capacitor (C): Passes high frequencies and blocks low frequencies. (High pass) Example: When it is required to set a crossover frequency of 120 Hz using speakers with an impedance of 4 ohms. fc=Cut of Frequency (Hz) R=Speaker Impedance (Ω) 2CAUTION • If you wish to bridge-connect a speaker, the speaker impedance must be no less than 4 ohms. Connecting a speaker with an impedance lower than 4 ohms may damage the unit. • Be sure to connect capacitors to speakers to which high frequencies will be passed. Failure to do so will result in a drop of the combined impedance with the subwoofer. • Ensure that the withstand voltage and current ratings of the capacitors (C) and coils (L) are sufficient. Left speaker Right speaker ■ Power wire connection POWER IN GND BATT. P.CON(REMOTE) BRIDGED LEFT RIGHT SPEAKER OUTPUT 234 POWER AMPLIFIER Lead terminal* Terminal cover Battery wire* Power control wire* Ground wire* Protective Fuse* Battery Subwoofer