Kenwood KDC-MP345U Instruction Manual - Page 9

FM2, FM3, and AM). You can recall a preset station without switching between bands. Í Beep: "KEY BEEP" ➤ "ON"*,"OFF" Setting the operation check sound (beep sound) ON/OFF. Î Built in AUX: "BUILTIN AUX"/"BUILT-IN AUX" ➤ "ON1"*,"ON2","OFF" When this is set to ON, AUX source can be selected. ON1: Outputs the sound of external unit connected to the AUX terminal when switched to AUX source. ON2: Activates the attenuator function when turning on the power with AUX source selected. Turn off the attenuator function when listening to output from external unit. This prevents the noise when no external unit is connected to AUX terminal. OFF: Disables the selection of AUX source. Set to OFF when not using the AUX terminal. Ï CD READ: "CD READ" ➤ "1"*, "2" Sets the method for reading CD. When unable to play special format CD, set this function to "2" to force playing. Note that some music CD may be unplayable even when set to "2". In addition, audio files cannot be played when set to "2". Normally, keep this set to "1". 1 : Automatically distinguishes between audio file disc and music CD when playing disc. 2 : Forces playing as music CD. Ì Switching Preout: "SWITCH PRE"/"SWITCH PREOUT" ➤ "REAR"*,"SUB-W" Switches the preout between rear output ("REAR") and subwoofer output ("SUB-W"). Ó Speaker Select: "SP SELECT" ➤ "OFF"*, "5/4", "6*9/6", "OEM" Fine-tuning so that the System Q value is optimal when setting the speaker type as follows; Speaker type OFF For 5 & 4 in. speaker For 6 & 6x9 in. speaker For the OEM speaker Display "SP OFF" "SP 5/4" "SP 6*9/6" "SP OEM" Ô Firmware Upgrade: "F/W UP xx.xx" ➤ "MEDIA USB"*, "MEDIA CD" Upgrades the firmware. Selecting "YES" and then pressing [VOL] knob starts upgrading the firmware. ⁄ • For how to update the firmware, access our web site. http://www.kenwood.com/cs/ce/  Demo Mode: "DEMO MODE" ➤ "ON"*, "OFF" Specifies whether to enable demonstration. Ò Subwoofer output: "SUB-W SET"/ "SUBWOOFER SET" ➤ "ON"*, "OFF" ⁄ • This setting can be made when "SUB-W" is selected for the item. Ú Bass Boost: "BASS BOOST" ➤ "LV1"*, "LV2", "OFF" " System Q: "SYSTEM Q" ➤ "NATURAL"*, "ROCK", "POPS", "EASY", "TOP 40", "JAZZ", "GAME", "USER" Switches between the following preset equalizer curves; Natural, Rock, Pops, Easy, Top 40, Jazz, Game, User setting ⁄ • "USER": This appears when Bass level, Middle level, and Treble level are adjusted. When the System Q setting is changed, the Bass, Middle, and Treble set replace the System Q values. Æ Bass level adjust: "BASS LEVEL" ➤ "-8" - "+ 8" å Middle level adjust: "MID LEVEL" ➤ "-8" - "+ 8" ß Treble level adjust: "TRE LEVEL" ➤ "-8" - "+ 8" ⁄ Source tone memory: Puts the set up value in the memory per source. ∂ Balance: "BALANCE" ➤ "L 15" - "R 15" ƒ Fader: "FADER" ➤ "R 15" - "F 15" © Subwoofer level adjust: "SUB-W LEVEL" ➤ "- 15" - "+ 15" ˙ Subwoofer Low Pass Filter: "LPF SUB-W"/ "LPF SUBWOOFER" ➤ "85", "120", "160", "THROUGH"(OFF)* Δ Subwoofer Phase: "SUB-W PHASE" ➤ "REV"/ "REVERSE"(180°), "NORM"/ "NORMAL"(0°)* ⁄ These adjustments can be made when "ON" is selected for the item. • Δ : This adjustment can be made when a setting other than "THROUGH" is selected for the item. Next page 3 English | 9