Kenwood KMR-D558BT User Manual - Page 17

AUDIO SETTINGS While listening to any source... 1 Press the volume knob to enter [FUNCTION]. 2 Turn the volume knob to select [AUDIO CONTROL], then press the knob. 3 Turn the volume knob to make a selection (see the following table), then press the knob. Repeat step 3 until the desired item is selected or activated. 4 Press and hold to exit. (or using RC-406) 1 Press AUD to enter [AUDIO CONTROL]. 2 Press J / K to make a selection, then press ENT IW. To return to the previous setting item or hierarchy, press . Default: XX SUB-W LEVEL -15 to +15 (0) Adjusts the subwoofer output level. BASS LEVEL MID LEVEL TRE LEVEL -8 to +8 (+6) -8 to +8 (+5) -8 to +8 (0) Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.) EQ PRO (for KDC-X598 ) BASS ADJUST BASS CTR FRQ 60/ 80/ 100/ 200HZ: Selects the center frequency. BASS LEVEL -8 to +8 (+6): Adjusts the level. BASS Q FACTOR 1.00/ 1.25/ 1.50/ 2.00: Adjusts the quality factor. BASS EXTEND ON: Turns on the extended bass. ; OFF: Cancels. MID ADJUST MID CTR FRQ 0.5/ 1.0/ 1.5/ 2.5KHZ: Selects the center frequency. MID LEVEL -8 to +8 (+5): Adjusts the level. MID Q FACTOR 0.75/ 1.00/ 1.25: Adjusts the quality factor. TRE ADJUST TRE CTR FRQ 10.0/ 12.5/ 15.0/ 17.5KHZ: Selects the center frequency. TRE LEVEL -8 to +8 (0): Adjusts the level. PRESET EQ DRIVE EQ/ TOP40/ POWERFUL/ ROCK/ POPS/ EASY/ JAZZ/ NATURAL/ USER: Selects a preset equalizer suitable to the music genre. (Select [USER] to use the customized bass, middle, and treble settings.) [DRIVE EQ] is a preset equalizer that reduces noise from the road. BASS BOOST LEVEL1/ LEVEL2/ LEVEL3: Selects your preferred bass boost level. ; OFF: Cancels. LOUDNESS LEVEL1/ LEVEL2: Selects your preferred low and high frequencies boost to produce a well-balanced sound at a low volume level. ; OFF: Cancels. SUBWOOFER SET ON: Turns on the subwoofer output. ; OFF: Cancels. LPF SUBWOOFER THROUGH: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/ 160HZ: Audio signals with frequencies lower than 85 Hz/ 120 Hz/ 160 Hz are sent to the subwoofer. SUB-W PHASE REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer output to be in line with the speaker output for optimum performance. (Selectable only if a setting other than [THROUGH] is selected for [LPF SUBWOOFER].) HPF THROUGH: All signals are sent to the speakers. ; 100HZ/ 120HZ/ 150HZ: Audio signals with frequencies higher than 100 Hz/ 120 Hz/ 150 Hz are sent to the speakers. FADER R15 to F15 (0): Adjusts the rear and front speaker output balance. BALANCE L15 to R15 (0): Adjusts the left and right speaker output balance. VOLUME OFFSET -8 to +8 (for AUX) ; -8 to 0 (for other sources): Presets the volume (Default: 0) adjustment level of each source. (Before adjustment, select the source you want to adjust.) SOUND RECNSTR ON: Creates realistic sound by compensating the high-frequency (Sound components and restoring the rise-time of the waveform that are lost reconstruction) in audio data compression. ; OFF: Cancels. [SUB-W LEVEL]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is selectable only if [SUBWOOFER SET] is set to [ON]. ENGLISH | 17