Kenwood KVT-745DVD Instruction Manual - Page 45
English 89
View all Kenwood KVT-745DVD manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 45 highlights
English Troubleshooting Guide The viewing angle cannot be changed. • The DVD disc being played does not contain the recording of more than one angle. • You are attempting to switch the angle in a DVD section where more than one angle is not recorded. • The viewing angle cannot be changed when the DVD disc being played does not contain the recording of more than one angle. • More than one viewing angle may be recorded only in limited sections in a disc. Playback will not start even after a title is selected. • A viewing restriction (RATING) has been set for the disc. • Check the viewing restriction level (RATING) setting. The voice or subtitle language selected in the initial setting is not played. • The DVD disc being played does not contain the recording of the selected voice or subtitle language. • Use a DVD disc containing the recording of the selected voice or subtitle language. ˙ Disc soruce The disc control mode cannot be selected. • No wire has been connected to the disc changer input terminal on the unit. • Connect the wire to the disc changer input terminal on the unit. The specified disc does not play, but another one plays instead. • The specified CD is quite dirty. • The CD is upside-down. • The disc is loaded in a different slot from that specified. • The disc is severely scratched. • Clean the CD. • Load the CD with the labeled side up. • Eject the disc magazine and check the number for the specified disc. • Try another disc instead. The sound skips. • Something is touching the disc changer. • The CD is scratched or dirty. • Remove whatever is touching it. • If skipping happens at the same place when the car is stopped, something with the CD is wrong. Clean the CD. The display shows that the changer is being played, but no sound can be heard. • The computer chip in the unit is not functioning normally. • Press the reset button on the unit (see page 4). The specified track will not play. • Random play or magazine random play has been selected. • Turn off random play or magazine random play. Track repeat, disc repeat, track scan, disc scan, random play, and magazine random play start by themselves. • The setting is not cancelled. • The settings for these functions remain on until the setting to off or the disc ejected, even if the power is turned off or the source changed. Can't remove disc. • The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF. • The disc can only be removed within 10 minutes of the ACC switch being turned OFF. If more than 10 minutes has elapsed, turn the ACC switch ON again and press the Eject button. 88 English ˙ MP3/WMA source Cannot play an MP3/WMA. • The media is scratched or dirty. • Clean the media, referring to the CD cleaning of the section on (see page 6). The sound skips when an MP3/WMA is being played. • The media is scratched or dirty. • The recording condition is bad. • Clean the media, referring to the CD cleaning of the section on (see page 6). • Record the media again or use another media. The MP3/WMA track time isn't displayed correctly. • --- • There are times when it isn't displayed correctly according to the MP3/WMA recording conditions. Can't display the ID3 tag information correctly. • Record is not made in conformity with the ID3 tag version 1.x. • Record in conformity with the ID3 tag version 1.x. Also, the display may be incorrect if an MP3 file uses the ID3 tag v1.x standard and if this standard has been expanded after production of the machine software. The following messages are displayed when certain problems are occurring in your system. Take the recommended actions. Hot Error Hold Error Mecha Error Disc Error Read Error Region code Error Parental level Error Error 07 - 67 The protective circuit in the unit activates when the temperature inside the unit exceeds 60°C (140°F), stopping all operation. ] Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F), the disc will start playing again. The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F), stopping all operation. ] Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F), the disc will start playing again. The disc player is malfunctioning. ] Eject the disc and try inserting it again. Contact the Kenwood dealer if this indicator continues blinking or the disc cannot be ejected. The unplayable discs is inserted. The disc is upside-down. ] Load the disc with the labeled side up. The disc is quite dirty. ] Clean the disc, referring to the section on (see page 6). The DVD software encoded for other region code. The parental level is set to high levels. The unit is malfunctioning for some reason. ] Press the reset button on the unit. If the "Error ##" code does not disappear, consult your nearest service center. English 89