Kenwood LZH-70W Installation Manual - Page 5

LZH-70W Installation Instructions - trim ring

Get Kenwood LZH-70W - LCD Monitor - External PDF manuals and user guides View all Kenwood LZH-70W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

9. Attach the optional trim ring (model #SK-70TR) to the console. 10. Using the marks on the roof as a guide, test-fit the console in its mounting location on the bracket assembly: a) Open the LCD screen to expose the console's mounting holes. b) Using the marks on the roof as a guide, hold the console against the mounting bracket in the mounting location. c) Mark the console's mounting screw hole locations on the bracket and drill pilot holes. d) Make sure screws are the correct length to avoid damaging the vehicle roof. 11. Wire all A/V input harnesses, A/V output harnesses, the Parental Interrupt/Mute button, IR sensors and power harness connections to the vehicle. • Route their multipin connectors to the console mounting location. • Power harness wiring: Red = Switched +12 V Accessory; Yellow = Constant +12 V; Black = Earth • Mount the Parental Interrupt/Mute button in a location easily accessible to the front-seat passengers. Step 9: Attaching the trim ring to the console 12. Route all wiring harnesses through the vehicle and through the access hole in the headliner. • Route the wiring so there is no excess at the console mounting location or above the headliner. 13. Re-attach the headliner. • Start from the centre of the roof and work out towards the sides, front, and rear. • Ensure that all headliner attachment points are aligned. • Re-install the visors and other hardware removed in Step 5. 14. Make all pigtail harness connections to the console. Step 10: Test-fitting the console on the bracket 15. Connect the vehicle's dome lamp wires to the LZH-70W Dome Light Wiring Harness: With all of the vehicle doors closed and the lights off, place the probes of a volt meter on the vehicle's dome light wires: a) If the meter shows 0 V, the vehicle has a Positive Switched system. Connect the LZH-70W's Dome Light Wiring Harness in the following way: • Blue wire --> vehicle's switched dome light wire • Orange wire --> fused constant 12 V source • Green wire --> a good earth point on the vehicle Step 14: Connecting the pigtails to the console LZH-70W Installation Instructions 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
9. Attach the optional trim ring (model #SK-70TR) to the
console.
10. Using the marks on the roof as a guide, test-fit the con-
sole in its mounting location on the bracket assembly:
a) Open the LCD screen to expose the console’s mounting
holes.
b) Using the marks on the roof as a guide, hold the
console against the mounting bracket in the mounting
location.
c) Mark the console’s mounting screw hole locations on
the bracket and drill pilot holes.
d) Make sure screws are the correct length to avoid
damaging the vehicle roof.
11. Wire all A/V input harnesses, A/V output harnesses,
the Parental Interrupt/Mute button, IR sensors and
power harness connections to the vehicle.
• Route
their
multipin
connectors
to
the
console
mounting location.
• Power harness wiring: Red = Switched +12 V Accessory;
Yellow = Constant +12 V; Black = Earth
• Mount the Parental Interrupt/Mute button in a location
easily accessible to the front-seat passengers.
12. Route all wiring harnesses through the vehicle and
through the access hole in the headliner.
• Route the wiring so there is no excess at the console
mounting location or above the headliner.
13. Re-attach the headliner.
• Start from the centre of the roof and work out towards the
sides, front, and rear.
• Ensure that all headliner attachment points are aligned.
• Re-install the visors and other hardware removed in
Step 5.
14. Make all pigtail harness connections to the console.
15. Connect the vehicle’s dome lamp wires to the
LZH-70W Dome Light Wiring Harness:
With all of the vehicle doors closed and the lights off, place
the probes of a volt meter on the vehicle’s dome light wires:
a) If the meter shows 0 V, the vehicle has a Positive
Switched system. Connect the LZH-70W’s Dome Light
Wiring Harness in the following way:
• Blue wire -->
vehicle’s switched dome light wire
• Orange wire --> fused constant 12 V source
• Green wire -->
a good earth point on the vehicle
LZH-70W Installation Instructions
5
Step 9: Attaching the trim ring to the console
Step 10: Test-fitting the console on the bracket
Step 14: Connecting the pigtails to the console