Kenwood PKT-23 User Manual 1 - Page 4

Basic Operation - programming

Get Kenwood PKT-23 PDF manuals and user guides View all Kenwood PKT-23 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

BASIC OPERATION SWITCHING POWER ON/ OFF Key type: Press [ ] to switch the transceiver ON. Press [ ] again to switch the transceiver OFF. Knob type: Turn the [Power switch/ Volume control] clockwise to switch the transceiver ON. Turn the [Power switch/ Volume control] counterclockwise fully to switch the transceiver OFF. ADJUSTING THE VOLUME Key type: Press the key programmed as [Volume Up] to increase the volume. Press the key programmed as [Volume Down] to decrease the volume. Knob type: Rotate the [Power switch/ Volume control] to adjust the volume. Clockwise increases the volume and counterclockwise decreases it. SELECTING THE ZONE AND CHANNEL Select the desired zone and channel using the keys programmed as [Zone Up]/ [Zone Down] and [Channel Up]/ [Channel Down]. TRANSMITTING 1 Select the desired zone and channel. 2 Press the key programmed as [Monitor] or [Squelch Off] to check whether or not the channel is free. • If the channel is busy, wait until it becomes free. 3 Press the PTT switch and speak into the microphone. Release the PTT switch to receive. • For best sound quality at the receiving station, hold the microphone approximately 3 cm to 4 cm (1.5 inches) from your mouth. RECEIVING Select the desired zone and channel. If signaling has been programmed on the selected channel, you will hear a call only if the received signal matches your transceiver settings. 3 < PO_BASIC_OP_PMR >

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
< PO_BASIC_OP_PMR >
3
BASIC OPERATION
SWITCHING POWER ON/ OFF
Key type:
Press
[
]
to switch the transceiver ON.
Press
[
]
again to switch the transceiver OFF.
Knob type:
Turn the
[Power switch/ Volume control]
clockwise to switch the transceiver ON.
Turn the
[Power switch/ Volume control]
counterclockwise fully to switch the transceiver OFF.
ADJUSTING THE VOLUME
Key type:
Press the
key programmed as
[Volume Up]
to increase the volume.
Press the
key programmed as
[Volume Down]
to
decrease the volume.
Knob type:
Rotate the
[Power switch/ Volume control]
to adjust the volume.
Clockwise increases the volume and counterclockwise
decreases it.
SELECTING THE ZONE AND CHANNEL
Select the desired zone and channel using the keys programmed as
[Zone Up]
/
[Zone Down]
and
[Channel Up]
/
[Channel Down]
.
TRANSMITTING
1
Select the desired zone and channel.
2
Press the key programmed as
[Monitor]
or
[Squelch Off]
to check whether or not the channel is free.
•
If the channel is busy, wait until it becomes free.
3
Press the
PTT
switch and speak into the microphone.
Release the
PTT
switch to receive.
•
For best sound quality at the receiving station, hold the microphone approximately
3 cm to 4 cm (1.5 inches) from your mouth.
RECEIVING
Select the desired zone and channel.
If signaling has been programmed on the selected channel, you will hear a call only if
the received signal matches your transceiver settings.