Kenwood TH-F7E User Manual - Page 48

Wireless Remote Control Th-f6a Only

Get Kenwood TH-F7E PDF manuals and user guides View all Kenwood TH-F7E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

WIRELESS REMOTE CONTROL (TH-F6A ONLY) If you also have a KENWOOD multi-band mobile transceiver, you can control one of its bands by sending DTMF tones from this portable transceiver. You will find this function useful when you want to control your mobile transceiver from a location outside your vehicle. Note: x You can remotely control only mobile transceivers that have both the DTSS and Remote Control functions. x The FCC rules permit you to send control codes only on the 70 cm band. PREPARATION Let us assume the 2 m band of the mobile transceiver will be controlled. On the portable transceiver: 1 Press [PTT]+[VFO]+[ ] (POWER). • The current secret access code number appears. The default is 000. 2 Press a numeric key (0 to 9) to enter a 3-digit secret number. • You can also turn the Tuning control or press [ ]/ [ ] to select each digit. Press [ ] (or [ ]) to move the cursor to the next (or previous) digit. 3 When the cursor is at the right most position, press [ ] to complete the setting. 4 Press [BAND] to select the 70 cm band. 5 Turn the Tuning control to select the transmit frequency. 6 Turn a transceiver power OFF. 7 Press [PTT]+[MR]+[ ] (POWER). • The transceiver enters Remote Control mode. "MOBILE CTRL" appears. • To exit Remote Control mode, repeat steps 6 and 7. On the mobile transceiver: 8 Program the DTSS code on the 70 cm band as the secret number. • Select the same number as you selected in step 2. • For the programming method, refer to the instruction manual of the mobile transceiver. 9 Select the receive frequency on the 70 cm band. • Mate this frequency with the transmit frequency on the portable transceiver. 10 Make the transceiver enter Remote Control mode. • For the method, refer to the instruction manual of the mobile transceiver. CONTROL OPERATION When in the Remote Control mode, the keys of the transceiver will function as below. Each time you press a key, the transceiver will automatically enter transmit mode and send the corresponding command to the mobile transceiver. 1 2 3 A REV ON1 TONE ON CTCSS ON ENT 4 5 6 B REV OFF1 TONE OFF CTCSS OFF TONE SEL 7 8 9 C CALL VFO MR (REP ON)2 0 # D DOWN LOW UP (REP OFF)2 1 TM-V7A/ TM-D700A: REV ON/ OFF TS-2000/ TS-B2000: DCS ON/ OFF Other mobile transceiver: TONE ALERT ON/ OFF 2 Switches Repeater function ON/ OFF if the mobile transceiver supports this function. To change the transmit/ receive frequency: [VFO] ¬ [ENT] ¬ [0] ~ [9] (enter the necessary digits) ¬ [ENT] Or [VFO] ¬ [UP]/ [DOWN] To recall a memory channel: [MR] ¬ [ENT] ¬ [0] ~ [9] (enter the necessary digits) ¬ [ENT] Or [MR] ¬ [UP]/ [DOWN] To change the tone (or CTCSS) frequency: [TONE SEL] ¬ [0] ~ [9] (enter 2 digits; ex. [0], [5]) ¬ [TONE SEL] • Refer to the Tone frequency table on your mobile transceiver for the Tone number. • Your mobile transceiver may require you to first activate the Tone or CTCSS function. It may also allow you to program a separate tone and CTCSS frequency. Refer to the instruction manual of the mobile transceiver. 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
43
WIRELESS REMOTE CONTROL (TH-F6A ONLY)
If you also have a
KENWOOD
multi-band mobile
transceiver, you can control one of its bands by
sending DTMF tones from this portable transceiver.
You will find this function useful when you want to
control your mobile transceiver from a location
outside your vehicle.
Note:
◆
You can remotely control only mobile transceivers that have both
the DTSS and Remote Control functions.
◆
The FCC rules permit you to send control codes only on the
70 cm band.
PREPARATION
Let us assume the 2 m band of the mobile transceiver
will be controlled.
On the portable transceiver:
1
Press
[PTT]+[VFO]+[
]
(POWER).
•
The current secret access code number
appears.
The default is 000.
2
Press a numeric key (0 to 9) to enter a 3-digit
secret number.
•
You can also turn the
Tuning
control or press
[
]
/
[
]
to select each digit.
Press
[
]
(or
[
]
)
to move the cursor to the next (or previous)
digit.
3
When the cursor is at the right most position,
press
[
]
to complete the setting.
4
Press
[BAND]
to select the 70 cm band.
5
Turn the
Tuning
control to select the transmit
frequency.
6
Turn a transceiver power OFF.
7
Press
[PTT]+[MR]+[
]
(POWER).
•
The transceiver enters Remote Control mode.
“MOBILE CTRL” appears.
•
To exit Remote Control mode, repeat steps 6
and 7.
On the mobile transceiver:
8
Program the DTSS code on the 70 cm band as the
secret number.
•
Select the same number as you selected in
step 2.
•
For the programming method, refer to the
instruction manual of the mobile transceiver.
9
Select the receive frequency on the 70 cm band.
•
Mate this frequency with the transmit frequency
on the portable transceiver.
10
Make the transceiver enter Remote Control mode.
•
For the method, refer to the instruction manual
of the mobile transceiver.
CONTROL OPERATION
When in the Remote Control mode, the keys of the
transceiver will function as below.
Each time you
press a key, the transceiver will automatically enter
transmit mode and send the corresponding command
to the mobile transceiver.
1
2
3
A
N
O
V
E
R
1
N
O
E
N
O
T
N
O
S
S
C
T
C
T
N
E
4
5
6
B
F
F
O
V
E
R
1
F
F
O
E
N
O
T
F
F
O
S
S
C
T
C
L
E
S
E
N
O
T
7
8
9
C
L
L
A
C
O
F
V
R
M
)
N
O
P
E
R
(
2
0
#
D
N
W
O
D
W
O
L
P
U
)
F
F
O
P
E
R
(
2
1
TM-V7A/ TM-D700A: REV ON/ OFF
TS-2000/ TS-B2000: DCS ON/ OFF
Other mobile transceiver:
TONE ALERT ON/ OFF
2
Switches Repeater function ON/ OFF if the mobile
transceiver supports this function.
To change the transmit/ receive frequency:
[VFO]
➡
[ENT]
➡
[0]
~
[9]
(enter the necessary
digits)
➡
[ENT]
Or
[VFO]
➡
[UP]
/
[DOWN]
To recall a memory channel:
[MR]
➡
[ENT]
➡
[0]
~
[9]
(enter the necessary digits)
➡
[ENT]
Or
[MR]
➡
[UP]
/
[DOWN]
To change the tone (or CTCSS) frequency:
[TONE SEL]
➡
[0]
~
[9]
(enter 2 digits; ex.
[0]
,
[5]
)
➡
[TONE SEL]
•
Refer to the Tone frequency table on your mobile
transceiver for the Tone number.
•
Your mobile transceiver may require you to first
activate the Tone or CTCSS function.
It may also
allow you to program a separate tone and CTCSS
frequency.
Refer to the instruction manual of the
mobile transceiver.