Kenwood TK-2200LV2P Instruction Manual - Page 26

Temporary Delete

Get Kenwood TK-2200LV2P - Protalk UHF - Radio PDF manuals and user guides
UPC - 019048179579
View all Kenwood TK-2200LV2P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

To start scanning, press the Side 2 key. • The LED indicator flashes green and scanning starts from the current channel and ascends through the channel numbers. • When a signal is detected on a channel and the QT/DQT matches, scan pauses at that channel and the LED indicator lights green. • When the signal is no longer present, scanning continues after 3 seconds (default). To end Scan, press the Side 2 key again. ■ Temporary Delete You can temporarily remove specific channels from the scanning sequence during Scan. When Scan pauses at a channel, you can remove that channel from the scanning sequence by pressing and holding the Side 2 key for 3 seconds. • You cannot remove a channel if there will be less than 2 channels available for scanning remaining. • To add the removed channels back into the Scan list, simply exit Scan mode or switch the transceiver power OFF and then ON again. TK-3200L (K3) Model: The default function of the Side 2 key is Calling Alert. Calling alert tones are used to identify yourself to your party members and inform them that you are about to make a call. To make a call using the calling alert tone, press and hold the PTT switch, then press the key programmed as Side 2. • The calling alert tone will transmit for the duration you press the Side 2 key. Note: The Side1 and Side2 keys can be reprogrammed {page 31}. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
±8
To start scanning, press the
Side 2
key.
•
The LED indicator flashes green and scanning starts from the current
channel and ascends through the channel numbers.
•
When a signal is detected on a channel and the QT/DQT matches,
scan pauses at that channel and the LED indicator lights green.
•
When the signal is no longer present, scanning continues after 3
seconds (default).
To end Scan, press the
Side 2
key again.
■
Temporary Delete
You can temporarily remove specific channels from the
scanning sequence during Scan.
When Scan pauses at a
channel, you can remove that channel from the scanning
sequence by pressing and holding the
Side 2
key for
3 seconds.
•
You cannot remove a channel if there will be less than
2 channels available for scanning remaining.
•
To add the removed channels back into the Scan list, simply exit
Scan mode or switch the transceiver power OFF and then ON
again.
TK-3200L (K3) Model:
The default function of the
Side 2
key is Calling Alert.
Calling alert tones are used to identify yourself to your party
members and
inform them that you are about to make a call.
To make a call using the calling alert tone, press and hold the
PTT
switch, then press the key programmed as
Side 2
.
•
The calling alert tone will transmit for the duration you press the
Side
2
key.
Note:
The
Side1
and
Side2
keys can be reprogrammed {page 3±}.