Kenwood XD-500 User Manual - Page 14

Operation of remote control unit

Get Kenwood XD-500 PDF manuals and user guides View all Kenwood XD-500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

1 4 Operation of remote control unit Loading batteries 1 Remove the cover. 2 Insert batteries. XD-750/700/550/500 (En) 3 Close the cover. Preparation section ÷ Insert two R6 ("AA"-size) batteries following the polarity indications. Operation Plug the power cord into the mains power outlet and press the (on/standby) key of the remote control unit to turn power ON. After the power has been turned ON, press the desired key. To turn power off, press the (on/standby) key again. The system enters the standby mode in which only the time display is lit. ÷ When pressing more than one remote control keys successively, press the keys securely by leaving an interval of 1 second or more between keys. 30° 30° Remote sensor 6 m Model: RC-H3R/H2R Infrared ray system Operating range (approx.) Notes 1. The provided batteries are intended for use in operation checking, and their service life may be short. 2. When the remote controllable distance becomes short, replace both of the batteries with new ones. 3. If direct sunlight or the light of a high- frequency fluorescent lamp (inverter type, etc.) is incident to the remote sensor, malfunction may occur. In such a case, change the installation position to avoid malfunction. Basic section Application section Knowledge sections

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
XD-750/700/550/500 (En)
14
Preparation section
Basic section
Application section
Knowledge sections
Operation
Loading batteries
2
Insert batteries.
3
Close the cover.
Plug the power cord into the mains power outlet and press
the
(on/standby) key of the remote control unit to
turn power ON. After the power has been turned ON, press
the desired key.
To turn power off, press the
(on/standby) key again.
The system enters the standby mode in which only the
time display is lit.
1. The provided batteries are intended for use in operation checking, and their service life may be short.
2. When the remote controllable distance becomes short, replace both of the batteries with new ones.
3. If direct sunlight or the light of a high- frequency fluorescent lamp (inverter type, etc.) is incident to the remote sensor, malfunction may occur.
In such a case, change the installation position to avoid malfunction.
1
Remove the cover.
Operation of remote control unit
Notes
Notes
Model: RC-H3R/H2R
Infrared ray system
Operating range (approx.)
30
°
6 m
Remote sensor
÷
When pressing more than one remote control keys successively,
press the keys securely by leaving an interval of 1 second or more
between keys.
÷
Insert two R6 (“AA”-size) batteries fol-
lowing the polarity indications.
30
°