Kenwood XR600-1 Instruction Manual - Page 2
Troubleshooting guide, Connection, Controls, Specifications
View all Kenwood XR600-1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
Connection / ৵ࢤ 7 RCA cable connections 7 ৵ࢤ3$"ভཌ Center unit (CD receiver, etc Power control wire RCA cable 3$"ভཌ 7 About the Lead Terminals 1. Wire Thicknesses You can use wires with the following thicknesses: Battery wire and AWG 4 - AWG 6 ground wire Speaker wire AWG 8 - AWG 16 2. Strip the wire Make a cut in the wire sheath (insulator made from vinyl, etc.) at the position 10-13 mm away from the end of the wire, and then remove the unnecessary portion of the sheath by twisting it. 3. Install the wire Loosen the screw using the supplied hexagon wrench. Insert the conductor of the wire in the terminal hole, and then tighten the screw. 7 8(̺"8( ֝ཌ 8(̺"8( b b b 10 - 13 mm 4 Parts included ࡱ (4.0 mm) Hexagon wrench ੂ࢘ϭ൭ 3 Parts included ࡱ (2.5 mm) Controls / ॥ᇅ 7 Fuse exchange 7 Insert the tip of thin-nose pliers into the slit, grasp the fuse and pull it out. b ᶇ ᶈ ᶉ ᶊ ᶋᶌ 1 Fuse (30 A x 3) NOTE If you can't find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal (BATT.) 3 Power control terminal (P.CON) Controls the unit ON/OFF. NOTE Controls the unit power. Be sure to connect it with all the systems. 4 Ground terminal (GND) 5 SPEAKER OUTPUT terminals As this unit accepts speakers with a minimum impedance of 2 ohm, connect speakers with 2- ohm or higher impedance to these terminals. 6 LINE IN terminal 7 LINE OUT terminal The signal that's input from the line input terminal is output. 8 INPUT SENSITIVITY control Set this control according to the pre-output level of the center unit connected with this unit. NOTE For the pre-output level, refer to the in the instruction manual of the center unit. 9 BASS BOOST LEVEL control Sets the low frequency level to be compensated. 0 LPF FREQUENCY control This control adjusts the frequency band output from this unit. - Power indicator When the power is turned on, the Power indicator lights. 1 Y ᇿ b 2#"55 ؊ሰ 31$0 b ᇿ b b 4(/% ࢤֹ ؊ሰ 541&",&3065165 b 6 7-*/&065 b 8*/1654&/4*5*7*5 b ᇿ b 9#"44#0045-&7 b 0-1''3&26 b b ణ ܈ 1C )H $E $S 7* 1## 1#%& ¯ ¯ ¯ ¯ ॿࡏ ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ 5 b 5 b c u v b b c bĎ aဪ॥ఖa a฿ཌa Troubleshooting guide What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. PROBLEM POSSIBLE CAUSE SOLUTION No sound. • Input (or output) cables are disconnected. • Connect the input (or output) cables. (No sound from one side.) (Blown fuse.) • Protection circuit may be activated. • Volume is too high. • The speaker cord is shorted. • Check connections by referring to . • Replace the fuse and use lower volume. • After check the speaker cord and fixing the cause of the short, replace the fuse. The output level is too • The input sensitivity adjusting control is • Adjust the control correctly referring to small (or too large). not set to the correct position. . The sound quality is • The speakers wire are connected with bad. wrong ª/· polarity. (The sound is distorted.) • A speaker wire is pinched by a screw in the car body. • The switches may be set improperly. • Connect them properly checking the ª/· of the terminals and wires well. • Connect the speaker wire again so that it is not pinched by anything. • Set switches properly by referring to . b b ჰၹ c b c b c b c b c b c b c b c b c b c b c b c b c b b c b c b c b Specifications Specifications subject to change without notice. Audio section Rated power output (+B = 14.4V) (4 Ω) (20 Hz - 200 Hz, ≤ 1.0 % THD 400 W × 1 (2 Ω) (100 Hz, ≤ 1.0 % THD 600 W × 1 Speaker impedance 4 Ω (2 Ω - 8 Ω allowable) Frequency Response (+0, -1 dB 20 Hz - 200 Hz Input sensitivity (RCA 0.2 V - 5.0 V Signal to noise ratio 100 dB Input impedance 10 kΩ Low pass filter frequency (-24 dB/oct.) 50 Hz - 200 Hz (variable) Bass Boost Control (40 Hz 0 - +18 dB (variable) General Operating voltage 14.4 V (11 - 16 V allowable) Current consumption 46 A Dimensions (W × H × D 220 × 35 × 169 mm Weight...1.6 kg ܿ۬ b ၻ҆ ܋ 7 7 7 Ȥ 5)% 8 Ȥ 5)% 8 NN ᶍ LH E# ਲૹ؇ 3$" 7 - 7 E# L E#PDU E# ॖэ