KitchenAid KBSD708MBS Owners Manual - Page 8
INSTALLATION REQUIREMENTS, Tools and Parts
View all KitchenAid KBSD708MBS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
INSTALLATION REQUIREMENTS Tools and Parts IMPORTANT: � Installer: Leave Installation Instructions with the homeowner. � Homeowner: Keep Installation Instructions for future reference. Save these Installation Instructions for the local electrical inspector's use. Tools Needed Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. � Cordless drill � Torx®†T27 screwdriver � Drill bits � 11/32" nut driver � Adjustable wrenches (2) � Appliance dolly � Phillips screwdriver � 5/32" hex key � Small level � Utility knife � 3/8" and 1/2" open-end wrenches � Tape measure � 1/4" and 5/16" socket drivers Parts Needed � #8 x 3" (7.6 cm) wood screws (longer screws may be needed) (6) � 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s) (1 or 2) � Make custom panels or consult a qualified cabinetmaker or carpenter to make the panels. Overlay Series: Make custom panels, or consult a qualified cabinetmaker or carpenter to make the panels. See "Overlay Series Custom Panels and Handle Kits" for more information. Stainless is shipped complete. � If you are connecting the water line directly to copper tubing and not to a shutoff valve, you need a ferrule, a union, and a 1/4" (6.35 mm) compression fitting. Location Requirements WARNING � Staff kitchen areas in shops, offices and other working environments. � Farm houses and by clients in hotels, motels and other residential type environments. � Bed and breakfast type environments. � Catering and similar non-retail applications. � Observe all governing codes and ordinances. � It is recommended that you do not install near an oven, radiator, or other heat source. � Do not install in a location where the temperature will fall below 55°F (13°C). � Floor must support the refrigerator weight, more than 600 lbs (272 kg), door panels and contents of the refrigerator. Flooring under refrigerator must be at same level as the room. Face of cabinetry must be plumb. � Ceiling height must allow for side tipping radius. See "Tipping Radius." � Location should permit door to open fully. See "Door Swing Dimensions." � Location must permit top grille removal. See "Opening Dimensions." Opening Dimensions � To avoid tipping during use, the solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced. If anti-tip boards are needed, they must be installed to the rear wall studs so that the bottom of the anti-tip board is 84" (213.4 cm) from the floor. See "Install Anti-Tip Boards" for more information. IMPORTANT � NOTES: • A clearance of 1/2" (1.3 cm) must be maintained above the top grille in order for the top grille to be removed. • Do not remove the foam gasket from the top of the compressor cover unless removal is necessary to fit the unit under a soffit. Removal of the gasket will cause loss in cooling efficiency. • If installing under a solid soffit, after, installation raise the leveling legs so that the gasket is pressed snugly against the soffit. Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from appliance. Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire. IMPORTANT: This refrigerator is designed for indoor, household use only. This appliance is intended to be used in household and similar applications such as: †TORX is a trademark of Acument Intellectual Properties, LLC. 8 A. Gasket B. Compressor cover � A grounded 3 prong electrical outlet should be located within a specified number of inches from the right-hand side cabinets or end panel. See the chart following the graphic for the number of inches required for your model. For more information, see "Electrical Requirements."