KitchenAid KBSN702MPA Quick Start Guide - Page 1
KitchenAid KBSN702MPA Manual
View all KitchenAid KBSN702MPA manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Built-in SXS Dispening Quick Start Guide OPERATING INSTRUCTIONS Measured Fill WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY Household water pressure may affect the accuracy of the Measured Fill feature. For optimum performance INSTRUCTIONS, located in your appliance's Owner's Manual, before operating this appliance. of your water dispenser, you must first calibrate Measured Fill. IMPORTANT: Before operating this appliance, make sure it has been properly installed according to the Calibrate Measured Fill appliance's Owner's Manual. 1. Press and hold the Measured Fill button for 3 seconds to enter Calibration Mode. The button will The Temperature Control UI is located above the external dispenser on the freezer door. For your display along with the 0.2 L or 8 oz default settings. convenience, your refrigerator and freezer controls are preset at the factory. 2. Pressing the water pad will dispense water (e.g., into a measuring cup) until the desired amount is For your convenience, your refrigerator and freezer temperature controls are set to the recommended set dispensed. Releasing the water pad will stop water dispensing. points at the factory. When you first install your refrigerator, make sure the temperature controls are still set Save and Exiting Calibration to the recommended set points. The recommended set points are 37°F (3°C) for the refrigerator and 0°F (-18°C) for the freezer. 1. If water was dispensed, pressing the Measured Fill button will save the amount dispensed, a tone will play and the calibration amount display will blink twice. IMPORTANT: ■ The recommended settings should be correct for normal household refrigerator use. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm. NOTE: Areas such as a garage, basement, or porch may have higher humidity or extreme temperatures. You may need to adjust the temperature away from the recommended settings to accommodate for these conditions. ■ When the power is on, the temperature display shows the set point temperature of the compartment. 2. If no water was dispensed, Pressing the Measured Fill button will exit Calibration mode without saving the calibration amount. NOTE: The amount of water you select will be dispensed. Be sure that the container is empty and can hold the entire volume. If ice is in the container, you may need to adjust your selection. Dispensing 1. Press MEASURED FILL to turn the feature on. When the feature is on, the Measured Fill screen appears on the display. ■ Wait 24 hours for your refrigerator to cool completely before adding food. If you add food before the refrigerator has cooled completely, your food may spoil. NOTE: Adjusting the refrigerator and freezer controls to a colder than recommended setting will not cool the compartments any faster. 2. To dispense water, press a sturdy glass against the water dispenser pad OR place the glass below the water dispenser and press the MEASURED FILL button. Hold the glass close to the water dispenser spout to ensure that the water dispenses into the glass. See "Measured Fill" section in Owner's Manual for additional instructions. ■ If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls. ■ Wait at least 24 hours between adjustments. Recheck the temperatures before other adjustments are made. Alarm Functions Door Open - The Door Ajar Alarm feature sounds an alarm when the refrigerator or freezer door is open for 5 minutes and the product cooling is turned on. The alarm will repeat every 2 minutes. Close both doors to turn it off. The feature then resets and will reactivate when either door is left open again for 5 minutes. Turning Refrigerator Cooling On/Off Your refrigerator and freezer will not cool when cooling is turned off. Follow the directions specific to your model. Turn ON ■ Press and hold Max Freeze and Max Cool buttons at the same time for 3 seconds. Cooling Off icon blinks twice and remains on. Setting the Temperature °F/°C preset at °F ■ Press and hold the Max Cool and FreshChill buttons at the same time for 3 seconds to change between Celsius and Fahrenheit. Adjusting Temperatures Power Outage - The power outage indicator lets you know if the power supply to the refrigerator has been cut off and the freezer temperature has risen to 18°F (-8°C) or higher. When power has been restored, the button repeatedly flashes and the red Power Outage icon appears. When the indicator is on, all other control and dispenser functions are disabled until you confirm that you are aware of the power outage. ■ To enable other functions, press Measured Fill to reset the display screen to its normal status. Miscellaneous Crisper Menu There are 4 preset temperatures for the Crisper Menu. Press the crisper menu button to select the desired option. Coldest to Warmest - Meats, Deli, Assorted, Produce. ■ MEAT setting is coldest setting and can be used for defrosting frozen items that need defrosting in the refrigerator. ■ PRODUCE setting is warmest setting and used for everyday vegetables and fruits. ■ ASSORTED setting is used to keep different items in the same drawer. ■ DELI setting is used for Deli meats and cheeses or non produce items. Ice Type Ice options include Cubed and Crushed Ice. Select the desired ice type to be dispensed by pressing the button which will display to confirm selection. Sound On/Off The following applies to both the refrigerator temperature button and freezer temperature button. Pressing the Freezer or Refrigerator picture button once will increase or decrease the temperature (1°C, 2°F). Once the temp setting reaches the lowest temperature allowed for that zone, the next button press will change the temperature to the highest temperature allowed for that zone (looping). The Refrigerator temperature range will be from 33°F to 43°F (1°C to 6°C), with the factory default temperature being 37°F (3°C). The Freezer temperature range will be from -8°F to 5°F (-22°C to -15°C), with the factory default temperature being 0°F (-18°C). CONDITION/REASON REFRIGERATOR too cold REFRIGERATOR too warm FREEZER too cold TEMPERATURE ADJUSTMENT REFRIGERATOR Control 1°C or 2°F higher REFRIGERATOR Control 1°C or 2°F lower FREEZER Control 1°C or 2°F higher ■ Press and hold [Max Cool] and [Refrigerator] button for 3 seconds and the sound off indicator will blink twice and remain on/off. ■ In Sound Off mode, the UI shall not make any sounds. The only exception to this is the door alarm. Control Lock Press and hold [Crisper] button and the Lock indicator will blink twice, play a tone and remain on/off. When Control Lock is active; ■ All other functions are not accessible. ■ Pressing any button will play invalid tone 3 times and lock indicator blinks 3 times. ■ Water/Ice paddles are not available, pressing the paddles will play invalid tone 3 times. Showroom Mode Demo mode for sales floor. Press and Hold the [RC Temp] + [FC Temp] buttons for 5 seconds, the showroom indicator will blink twice to remain on/off. Vacation Mode See "Vacation Care" section in the Owner's Manual for instructions. Dispenser Lighting ■ Quickly press the Light button to turn the dispenser light ON. ■ Quickly press the button again to turn the light OFF. FREEZER too warm/too little ice FREEZER Control 1°C or 2°F lower Water Filter Indicator and Reset (all models) The water filter indicator, located on the control panel, will help you know when to change the water filter. Replace status: ■ When the dispenser control panel's water filter status displays, this tells you that it is almost time to change the water filter cartridge. Replace the water filter cartridge. Replace Overdue status: ■ When the light turns red on the control panel, this tells you that it is time to change the water filter cartridge. ■ It is recommended that you replace the filter when the status light turns red or water flow to your water dispenser or ice maker decreases noticeably. NOTE: If water flow to your water dispenser or ice maker decreases noticeably, change the filter sooner. The filter should be replaced at least every 6 months, depending on your water quality and usage. When dispensing water after the Replace Filter icon is on, the Replace Filter icon blinks for the duration of dispensing. This applies for both the Replace Filter state and Replace Overdue status. Fourteen days after the Replace Filter indicator turns On, it shall enter "Replace Overdue" mode. Online Ordering Information For detailed installation instruction and maintenance information, winter storage, and transportation tips, please see the Owner's Manual included with your appliance. For information on any of the following items, the full cycle guide, warranty, detailed product dimensions, or for complete instructions for use and installation, please visit https://www.kitchenaid.com/service-and-support, or in Canada https://www.kitchenaid.ca/service-and-support. This may save you the cost of a service call. However, if you need to contact us, use the information listed below for the appropriate region. To purchase additional bakeware please visit: https://www.kitchenaid.com/kitchenware/bakeware United States: 1-800-422-1230 KitchenAid Brand Home Appliances Customer eXperience Center 553 Benson Road Benton Harbor, MI 49022-2692 Canada: 1-800-807-6777 KitchenAid Brand Home Appliances Customer eXperience Centre 200-6750 Century Ave. Mississauga, Ontario L5N 0B7 Filter Reset After changing the filter, press and hold Filter Reset button for 3 seconds. The button will no longer display once reset. See the "Water Filtration System" section in Owner's Manual for steps to remove and replace filter. Max Cool/ Max Freeze Max Cool The Max Cool feature assists with periods of high refrigerator use, full grocery loads, or temporarily warm room temperature. ■ Press Max Cool to set the freezer and refrigerator to the lowest temperature settings. Press Max Cool again to return to the normal refrigerator set point. NOTE: The Max Cool feature will shut off automatically in approximately 12 hours. Get Started with your built-in refrigerator. Scan to see top features, tips and how-to videos. SAVE THESE INSTRUCTIONS ■ While Max Cool is ON, changing the refrigerator temperature will deactivate Max Cool. ■ While Max Cool is ON, activating Vacation Mode will deactivate Max Cool. Max Freeze The Max Freeze feature assists with temporary periods of heavy ice use by increasing ice production. ■ Press Max Freeze to set the freezer to the lowest temperature setting. Press the Max Freeze feature touch pad again to return to the normal freezer set point. ■ While Max Freeze is ON, changing the freezer temperature will deactivate Max Freeze. NOTE: The Max Freeze feature will shut off automatically in approximately 48 hours. W11490762E W11568134E-SP