KitchenAid KDFE104KBL Cycle Guide - Page 2

Dishwasher Feedback

Get KitchenAid KDFE104KBL PDF manuals and user guides View all KitchenAid KDFE104KBL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

CONTROL START CANCEL DELAY DISHWASHER FEEDBACK PURPOSE COMMENTS Press to start or resume a wash cycle. Push to reset any cycle or options during selection. Push to end a cycle once started. If the door is opened during a cycle or power is interrupted, Start/Resume indicator light flashes. Cycle will not resume until door is closed and Start/Resume is pressed. NOTE: Push door firmly closed within 4 seconds of pressing Start/Resume. If door is not closed within 4 seconds, the Start/ Resume button light will flash, an audible tone will be heard, and cycle will not start. Close door firmly. The dishwasher starts a 2 minutes drain (if needed). Let dishwasher drain completely. To delay the start: Runs the dishwasher at a later time 1. Select a wash cycle and options. 2. Press DELAY. Each time you press Delay, it will display the next available delay time. 3. Press START to begin the delay countdown. NOTE: If the door is opened, such as to add a dish, the Start button must be pressed to resume the delay countdown. Cancelling a Cycle 1. Open the door slightly to stop the cycle. Wait for the spraying action to stop before completely opening the door. 2. Press and hold CANCEL/DRAIN for 4 seconds. The CANCEL/ DRAIN light will turn on. 3. Close the door, and the dishwasher starts a drain cycle (if water remains in bottom of dishwasher). Let the dishwasher drain completely. The Cancel/Drain light turns off after 3 minutes. Changing a Cycle After Dishwasher Is Started You can interrupt a cycle and restart the dishwasher from the beginning using the following procedure. 1. Open the door slightly to stop the cycle. Wait for the spraying action to stop, then open the door completely. 2. Check that detergent dispenser cover is still closed. If cover is open, you will need to refill the detergent dispenser before restarting the new cycle. 3. Press CANCEL/DRAIN to reset the control. 4. Select new cycles and options. 5. Press START/RESUME. Adding a Dish After Dishwasher is Started 1. Open the door slightly to stop the cycle. Wait for the spraying action to stop, then open the door completely. 2. Check whether the detergent dispenser cover is still closed. If it is open, the wash cycle has already started and adding a dish is not recommended. 3. If detergent has not yet been used (detergent dispenser cover is closed), you may add a dish. 4. Push door firmly closed and press START/RESUME within 4 seconds. If you take too long, the Start keypad light flashes, and you will hear an audible tone. Press START/RESUME again and close the door within 4 seconds.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
DISHWASHER FEEDBACK
CONTROL
PURPOSE
COMMENTS
START
Press to start or resume a wash
cycle.
If the door is opened during a cycle or power is interrupted,
Start/Resume indicator light flashes. Cycle will not resume until
door is closed and Start/Resume is pressed.
NOTE:
Push door firmly closed within ± seconds of pressing
Start/Resume. If door is not closed within 4 seconds, the Start/
Resume button light will flash, an audible tone will be heard,
and cycle will not start.
CANCEL
Push to reset any cycle or options
during selection. Push to end a
cycle once started.
Close door firmly. The dishwasher starts a ² minutes drain (if
needed). Let dishwasher drain completely.
DELAY
Runs the dishwasher at a later
time
To delay the start:
1.
Select a wash cycle and options.
2.
Press DELAY. Each time you press Delay, it will display the
next available delay time.
3.
Press START to begin the delay countdown.
NOTE:
If the door is opened, such as to add a dish, the Start
button must be pressed to resume the delay countdown.
Cancelling a Cycle
1.
Open the door slightly to stop the cycle. Wait for the spraying
action to stop before completely opening the door.
2.
Press and hold CANCEL/DRAIN for 4 seconds. The CANCEL/
DRAIN light will turn on.
3.
Close the door, and the dishwasher starts a drain cycle (if wa-
ter remains in bottom of dishwasher). Let the dishwasher drain
completely. The Cancel/Drain light turns off after 3 minutes.
Changing a Cycle After Dishwasher Is Started
You can interrupt a cycle and restart the dishwasher from the
beginning using the following procedure.
1.
Open the door slightly to stop the cycle. Wait for the spraying
action to stop, then open the door completely.
2.
Check that detergent dispenser cover is still closed. If cover
is open, you will need to refill the detergent dispenser before
restarting the new cycle.
3.
Press CANCEL/DRAIN to reset the control.
4.
Select new cycles and options.
5.
Press START/RESUME.
Adding a Dish After Dishwasher is Started
1.
Open the door slightly to stop the cycle. Wait for the spraying
action to stop, then open the door completely.
2.
Check whether the detergent dispenser cover is still closed.
If it is open, the wash cycle has already started and adding a
dish is not recommended.
3.
If detergent has not yet been used (detergent dispenser cover
is closed), you may add a dish.
4.
Push door firmly closed and press START/RESUME within ±
seconds. If you take too long, the Start keypad light flashes,
and you will hear an audible tone. Press START/RESUME
again and close the door within 4 seconds.