KitchenAid KDRS463VSS Installation Guide - Page 4

WARNING Tip Over Hazard A child or adult can tip the range and be killed. Connect anti-tip bracket to wall behind range. Reconnect the anti-tip bracket, if the range is moved. Failure to follow these instructions can result in death or serious burns to children and adults. INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed ■ Burner grates ■ Burner heads and caps ■ Grill grate (on grill models) ■ Tape measure ■ #2 Phillips screwdriver carbide tip masonry bit ■ Marker or pencil ■ Wave tray (on grill models) ■ Flame spreader (on grill models) x 4¼" flat-blade screwdriver ■ Pipe-joint compound resistant to LP gas ■ Burner assembly (on grill models) ■ Grease trays (2) (on grill models) ■ Level ■ Drill ■ Wrench or pliers ■ Noncorrosive leak-detection solution ■ Tubing cutter ■ Griddle drip tray (on griddle models) ■ Grill drip tray (on grill models) ■ Island trim ■ Pipe wrench ■ Adjustable wrench or ⁵⁄₈" wrench drive ratchet drill bit combination wrench nut drivers For LP/Natural Gas Conversions ■ T15 Torx®† screwdriver socket ■ Adjustable wrench ■ ½" deep-well socket ■ 7 mm nut driver ■ Masking tape Parts supplied Check that all parts are included. ■ Anti-tip bracket kit ■ LP orifice package (W10221288) ■ Conversion label (W10221320) NOTE: The cooktop is manufactured for use with Natural gas. To convert to LP gas, see the "Gas Conversions" section. Additional Parts Supplied on Steam-Assist Models ■ Model W10049700 water filter kit ■ ¼" to ¼" water supply union Parts needed ■ Power supply cord kit: ■ 30" (76.2 cm) and 36" (91.4 cm) models - A UL listed 40 amp power supply cord kit ■ 48" (121.9 cm) models - A UL listed 50 amp power supply cord kit marked for use with nominal 1³⁄₈" (34.93 mm) diameter connection openings ■ A UL listed strain relief ■ UL listed wire connectors A B A. Anti-tip bracket B. #8-18 x 1" Phillips head screws (4) ■ All models must be installed with a backguard if installing at zero clearance to a combustible backwall. See "Cabinet Dimensions" in the "Location Requirements" section for installation requirements. ■ 30" (76.2 cm) Adjustable Backguard Order Part Number 8285148 ■ 36" (91.4 cm) Adjustable Backguard Order Part Number 8284756 NOTE: Anti-tip bracket must be securely mounted to subfloor. Thickness of flooring may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store. See "Install Anti-Tip Bracket" section. ■ Gas pressure regulator ■ 48" (121.9 cm) Adjustable Backguard Order Part Number 8284755 ■ 9" (22.9 cm) Backguard for 30" (76.2 cm) Ranges Order Part Number W10115773 ■ 9" (22.9 cm) Backguard for 36" (91.4 cm) Ranges Order Part Number W10115776 †®TORX is a registered trademark of Saturn Fasteners, Inc. ■ 9" (22.9 cm) Backguard for 48" (121.9 cm) Ranges Order Part Number W10115777 4