KitchenAid KEMC378KSS Installation Instructions - Page 4
Electrical connection B, Attachment C, Check operation D, WARNING - installation instructions
View all KitchenAid KEMC378KSS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
B Electrical connection junction cable from power supply If your house has aluminum wiring, see box "Electrical requirements", Page 2. red wires black wires WARNING white wire junction box red wires cable from power supply white wires Electrical Shock Hazard Turn power supply off before connecting wires. Use 8 gauge solid copper wire. Electrically ground range. Failure to follow these instructions can result in death, fire, or electrical shock. This oven is manufactured with white (neutral) power supply wire and a cabinet-connected bare grounding wire twisted together. 4. Feed oven cable through opening in the cabinet. Make electrical connection following the steps needed for your installation. 1. Disconnect the power supply. 2. Remove the junction box cover. 3. Connect oven cable to junction box through the U.L.-listed conduit connector. 4. Connect the two black wires together with twist-on connectors. 5. Connect the two red wires together with twist-on connectors. 6. Complete electrical connection according to local codes and ordinances. white and bare grounding oven cable wires - factory crimped Figure 1 cable from oven U.L.-listed conduit connector If local codes PERMIT connecting cabinet-grounding conductor to neutral white wire in junction box: 7. Connect the factory-crimped bare and white oven cable wires to the neutral (white) wire in junction box. See Figure 1. 8. Replace junction box cover. bare grounding wires Figure 2 cable from oven black wires U.L.-listed conduit connector If local codes DO NOT PERMIT connecting cabinet-grounding conductor to neutral white wire in junction box: If connecting to a four-wire electrical system: 7. Separate the factory-crimped bare and white oven cable wires. 8. Connect white oven cable wire to neutral (white) wire in junction box. See Figure 2. 9. Connect the bare grounding oven cable wire to a grounded wire in the junction box. See Figure 2. 10. Replace junction box cover. 7. Separate bare and white oven cable wires. 8. Connect white oven cable wire to neutral (white) wire in junction box. See Figure 2. 9. Connect the bare grounding oven cable wire to the green grounding wire in junction box. Do Not connect bare grounding wire to neutral (white) wire in junction box. See Figure 2. 10. Replace junction box cover. C Attachment Carefully push against seal area of oven front frame when pushing oven into cabinet. Do Not push against outside edges. 5. Lift oven into cabinet cutout using the oven opening as an area to grip. shipping foot Push against seal area of front frame to push oven into cabinet until shipping feet almost contact cabinet. Use a Phillips screwdriver to remove screws attaching shipping feet. Remove and discard shipping feet. Push oven completely into cabinet and center oven in cabinet cutout. 4 screws 6. Important: Securely fasten oven to cabinet using the screws provided (two screws for a single oven or four screws for a double oven). Insert the screws through holes in mounting rails. Do Not overtighten screws. Slide top of trim up. Push trim into place. Replace trim screw. 8. Replace oven racks. 9. Reinstall the oven door by inserting ends of hinges into hinge slots in the oven frame. Push hinges in as far as they will go. Open the door (you will feel the door drop into place) and rotate both hinge latches back to the locked position. Close and open the door to check that the door closes and opens completely. If door does not close or open completely, repeat the door removal step and reinstall door as described above. 7. Slide top end of each trim upward onto oven side rails. Push each trim into place at bottom of trim. Use screws to attach each trim to oven. Take care not to scratch other surfaces with ends of trim. D Check operation 10. Turn on power supply. The display panel will light up briefly. "PF" should appear in the temperature display. BAKE BROIL CLEAN 11. Check the operation of your lower oven. Press the "BROIL" pad. "BROIL" will appear in the display. Press the "START" pad. Page 3 Make sure the oven door is closed and the "ON" light is shown in the display area. After 2 minutes, partially open oven door. You should feel heat from the oven. Press the "CANCEL" pad. If your oven does not heat or an"F" appears in the display, contact your dealer or check the "If you need service..." section of this Installation Instructions. 12. Check the operation of the microwave oven. • Fill a microwave-safe container with one cup of water and place container inside microwave oven. Close door firmly. • Set microwave oven cook time to "2:00" minutes. • Press the "START/ENTER" pad. The interior microwave oven light should be on and the remaining cooking time should be displayed. • When display reads "1:00," open microwave oven door. The microwave should stop cooking. • Close door firmly. The interior microwave oven light should turn off. • Press the "START/ENTER" pad. Microwave oven should begin cooking and the microwave oven interior light should be on. • Let microwave oven complete cooking time. A tone will sound four times at end of cooking time and microwave oven will shut off. • Open microwave oven door and carefully remove container. Water in container should be hot. To get the most efficient use from your new oven, read your Use and Care Guide. Keep Installation Instructions and Guide close to oven for easy reference.