KitchenAid KRFC302EPA Use & Care Guide - Page 12

Handle Installation and Removal - handles

Get KitchenAid KRFC302EPA PDF manuals and user guides View all KitchenAid KRFC302EPA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

INSTALLATION INSTRUCTIONS 4. Install the water supply tube clamp around the water supply line to reduce strain on the coupling. 5. Turn shutoff valve ON. 6. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak. 7. On some models, the ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the ¹⁄₄" (6.35 mm) water line at either tube connection. Obtain a water strainer from your appliance dealer. Complete the Installation WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Handle Installation and Removal 1. Plug into a grounded 3 prong outlet. 2. Flush the water system. See "Water and Ice Dispensers." NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill the ice storage bin. Parts Included: Door handles (2), Drawer handle(s) (1 or 2 depending on model hex key, spare setscrew(s) NOTE: With the handles laying on a flat surface, the handles intended for the drawers are more curved. They will not mount flush against the doors. Install Handles NOTE: Handle mounting setscrews are preinstalled inside the handle. 1. Remove the handles from the packaging inside the refrigerator, and place them on a soft surface. 2. Open a refrigerator compartment door. On the closed door, place a handle onto the shoulder screws so that the setscrews are facing the adjacent door. 3. Firmly push the handle toward the door until the handle base is flush against the door. 4. While holding the handle, insert the short end of the hex key into the upper hole and slightly rotate the hex key until it is engaged in the setscrew. A B A. Shoulder screws B. Setscrews inside the handle 12 5. Using a clockwise motion tighten the setscrew just until it begins to contact the shoulder screw. Do not fully tighten. 6. Repeat steps 4 and 5 to fasten the lower setscrew. 7. Once both setscrews have been partially tightened as instructed in the previous steps, fully tighten both setscrews. IMPORTANT: When the screws feel tight, tighten them an additional quarter-turn. The handle is not properly installed without this extra tightening.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
12
INSTALLATION INSTRUCTIONS
4.
Install the water supply tube clamp around the water supply
line to reduce strain on the coupling.
5.
Turn shutoff valve ON.
6.
Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
7.
On some models, the ice maker is equipped with a built-in
water strainer. If your water conditions require a second water
strainer, install it in the ¹/
₄
" (6.35 mm) water line at either tube
connection. Obtain a water strainer from your appliance
dealer.
Complete the Installation
1.
Plug into a grounded 3 prong outlet.
2.
Flush the water system. See “Water and Ice Dispensers.”
NOTE:
Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to
completely fill the ice storage bin.
Handle Installation and Removal
Parts Included:
Door handles (2), Drawer handle(s) (1 or 2
depending on model), ¹/
₈
" hex key, spare setscrew(s)
NOTE:
With the handles laying on a flat surface, the handles
intended for the drawers are more curved. They will not mount
flush against the doors.
Install Handles
NOTE:
Handle mounting setscrews are preinstalled inside the
handle.
1.
Remove the handles from the packaging inside the
refrigerator, and place them on a soft surface.
2.
Open a refrigerator compartment door. On the closed door,
place a handle onto the shoulder screws so that the
setscrews are facing the adjacent door.
3.
Firmly push the handle toward the door until the handle base
is flush against the door.
4.
While holding the handle, insert the short end of the hex key
into the upper hole and slightly rotate the hex key until it is
engaged in the setscrew.
5.
Using a clockwise motion tighten the setscrew just until it
begins to contact the shoulder screw. Do not fully tighten.
6.
Repeat steps 4 and 5 to fasten the lower setscrew.
7.
Once both setscrews have been partially tightened as
instructed in the previous steps, fully tighten both setscrews.
IMPORTANT:
When the screws feel tight, tighten them an
additional quarter-turn. The handle is not properly installed
without this extra tightening.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
A. Shoulder screws
B. Setscrews inside the handle
A
B