KitchenAid KRFC704FBS Installation Guide - Page 21

Door Panel Installation, Top Grille Panel

Get KitchenAid KRFC704FBS PDF manuals and user guides View all KitchenAid KRFC704FBS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Door Panel Installation 1. Remove all tape and door bracing from the refrigerator door(s) and freezer drawer. 2. Open the refrigerator door(s) and freezer drawer and remove the trims and corner caps on each door as shown. 5. Remove the film from the screw covers. Snap the screw covers into the handle trim section. A A B B Top Grille Panel 1. Grasp both ends of the top grille. 2. Push straight up; then pull straight out. Place the top grille panel-side down on a soft working surface. B A B C A A A. Corner caps B. Refrigerator door trims C. Freezer drawer trim 3. Slide the custom panels into the trims on the refrigerator door(s) and freezer drawer, making sure that the backer panel fits into the hinge side trims. A. Top grille B. Cabinet side trims 3. Remove one end cap by loosening the nuts and sliding the end cap off. A C B D A. Bottom rail B. Nuts C. End cap D. Top rail 4. Slide the custom panel into the top grille channel and reattach the end cap. A A A. Panels 4. Reinstall the trims and corner caps. A A. Custom panel 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
21
Door Panel Installation
1.
Remove all tape and door bracing from the refrigerator
door(s) and freezer drawer.
2.
Open the refrigerator door(s) and freezer drawer and remove
the trims and corner caps on each door as shown.
3.
Slide the custom panels into the trims on the refrigerator
door(s) and freezer drawer, making sure that the backer panel
fits into the hinge side trims.
4.
Reinstall the trims and corner caps.
5.
Remove the film from the screw covers. Snap the screw
covers into the handle trim section.
Top Grille Panel
1.
Grasp both ends of the top grille.
2.
Push straight up; then pull straight out. Place the top grille
panel-side down on a soft working surface.
3.
Remove one end cap by loosening the nuts and sliding the
end cap off.
4.
Slide the custom panel into the top grille channel and
reattach the end cap.
A. Corner caps
B. Refrigerator door trims
C. Freezer drawer trim
A. Panels
B
A
B
A
C
A
A
A
A
A. Top grille
B. Cabinet side trims
A. Bottom rail
B. Nuts
C. End cap
D. Top rail
A. Custom panel
B
B
A
C
B
A
D
A