KitchenAid KSM100PSWW Use & Care Guide - Page 14

Assembling Your Tilt-head Stand Mixer, Using Your Pouring Shield

Get KitchenAid KSM100PSWW - Ultra Power Plus Stand Mixer PDF manuals and user guides
UPC - 883049036908
View all KitchenAid KSM100PSWW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

ENGLISH ASSEMBLING YOUR TILT-HEAD STAND MIXER To Operate Speed Control Speed control lever should always be set on lowest speed for starting, then gradually moved to desired higher speed to avoid splashing ingredients out of bowl. See page 15 for Speed Control Guide. Speed Control To Lock Motor Head 1. Make sure motor head is completely down. 2. Place locking lever in LOCK position. 3. Before mixing, test lock by attempting to raise head. Lock Unlock To Unlock Motor Head 1. Place lever in UNLOCK position. NOTE: Motor head should always be kept in LOCK position when using mixer. USING YOUR POURING SHIELD* To Attach Pouring Shield 1. Turn speed control to OFF. 2. Unplug Stand Mixer or disconnect power. 3. Attach Flat Beater, Dough Hook, or Wire Whip and bowl (see page 11). 4. From the front of the mixer, slide the Pouring Shield over the bowl until the shield is centered. The bottom rim of the shield should fit within the bowl. To Remove Pouring Shield 1. Turn speed control to OFF. 2. Unplug Stand Mixer or disconnect power. 3. Lift the front of the Pouring Shield clear of the bowl rim and pull forward. 4. Remove attachment and bowl. Pouring Chute To Use Pouring Shield 1. For best results, rotate the shield so the motor head covers the "u" shaped gap in the shield. The pouring chute will be just to the right of the attachment hub as you face the mixer. 2. Pour the ingredients into the bowl through the pouring chute. * If Pouring Shield is included. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
12
ENGLISH
To Operate Speed Control
Speed control lever should always be
set on lowest speed for starting, then
gradually moved to desired higher
speed to avoid splashing ingredients
out of bowl. See page 15 for Speed
Control Guide.
To Lock Motor Head
1.
Make sure motor head is
completely down.
2.
Place locking lever in LOCK
position.
3.
Before mixing, test lock by
attempting to raise head.
To Unlock Motor Head
1.
Place lever in UNLOCK position.
NOTE:
Motor head should always be
kept in LOCK position when using mixer.
ASSEMBLING YOUR TILT-HEAD STAND MIXER
Lock
Unlock
Speed Control
To Attach Pouring Shield
1.
Turn speed control to OFF.
2.
Unplug Stand Mixer or
disconnect power.
3.
Attach Flat Beater, Dough Hook,
or Wire Whip and bowl (see
page 11).
4.
From the front of the mixer, slide
the Pouring Shield over the bowl
until the shield is centered. The
bottom rim of the shield should fit
within the bowl.
To Remove Pouring Shield
1.
Turn speed control to OFF.
2.
Unplug Stand Mixer or
disconnect power.
3.
Lift the front of the Pouring Shield
clear of the bowl rim and
pull forward.
4.
Remove attachment and bowl.
To Use Pouring Shield
1.
For best results, rotate the shield
so the motor head covers the “u”
shaped gap in the shield. The
pouring chute will be just to the
right of the attachment hub as you
face the mixer.
2.
Pour the ingredients into the bowl
through the pouring chute.
USING YOUR POURING SHIELD*
Pouring Chute
* If Pouring Shield is included.