KitchenAid KSSC42FTS Installation Guide - Page 16

Classic Series Custom Panels If you plan to install custom wood panels, you will need to create the panels yourself or consult a qualified cabinetmaker or carpenter. See dimension drawings for panel specifications. IMPORTANT: Panels weighing more than recommended may cause damage to your refrigerator. NOTE: Dimensions shown have a 1.5 mm) tolerance. Panels that are more than ¹⁄₄" (6.35 mm) thick must be routed. If panels are less than ¹⁄₄" (6.35 mm) thick, install a filler panel between the doors and decorative panels. NOTES: ■ If the standard handle is used, the handle side offset of both panels should be 3¹⁄₄" (8.25 cm) to all for finger clearance. ■ If an extended handle is used, the handle side offset of both panels should be 1.1 cm). Make sure the refrigerator location allows the doors with extended handles to open to 90 degrees. See "Door Swing Dimensions." Top Grille Panel ■ The dashed lines in the illustration represent the location and offsets of raised wood panel. The top grille panel should not weigh more than 10 lbs (4.5 kg). NOTE: The dashed lines in the illustration represent the location and offsets of raised wood panel. A 7" (17.78 cm) ¹⁄₄" thick plywood Top & Bottom Offsets 1.75 cm) Model A 36 34¹⁄₄" (87.0 cm) 42 40¹⁄₄" (102.2 cm) 48 46¹⁄₄" (117.5 cm) Side Offsets 1.11 cm) Door Panels for Non-dispenser Models The freezer panel should not weigh more than 40 lbs (18.1 kg). The refrigerator panel should not weigh more than 50 lbs (23 kg). A B ¹⁄₂" (1.27 cm) Freezer Door (Non-Dispenser) Refrigerator Door ¹⁄₂" (1.27 cm) Door Panels for Dispenser Models The freezer panel should not weigh more than 40 lbs (18.1 kg). The refrigerator panel should not weigh more than 50 lbs (23 kg). A B ¹⁄₂" (1.27 cm) ¹⁄₄" thick plywood Freezer Door (Dispenser) Refrigerator Door ¹⁄₂" (1.27 cm) 14¹⁄₄" (36.2 cm) 10⁷⁄₈" (27.6 cm) 70 178.9 cm) 33³⁄₄" (85.7 cm) Dispenser cutout is centered left-to-right 3¹⁄₄" (8.3 cm) 1.1 cm) 3¹⁄₄" (8.3 cm) ¹⁄₄" thick plywood ⁄₄" thick ywood 70 178.9 cm) 3¹⁄₄" (8.3 cm) 1.1 cm) 3¹⁄₄" (8.3 cm) ¹⁄₄" thick plywood 1.1 cm) ¹⁄₂" Location and offsets (1.27 cm) of raised wood panel ¹⁄₂" (1.27 cm) Model A B 36 14¹⁄₄" (36.2 cm) 19¹⁄₄" (48.9 cm) 42 16³⁄₄" (42.6 cm) 22³⁄₄" (57.8 cm) 48 19¹⁄₄" (48.9 cm) 26¹⁄₄" (66.7 cm) 16 1.1 cm) ¹⁄₂" Location and offsets (1.27 cm) of raised wood panel ¹⁄₂" (1.27 cm) Model A B 36 14¹⁄₄" (36.2 cm) 19¹⁄₄" (48.9 cm) 42 16³⁄₄" (42.6 cm) 22³⁄₄" (57.8 cm) 48 19¹⁄₄" (48.9 cm) 26¹⁄₄" (66.7 cm) NOTES: ■ Dispenser cutout is centered left-to-right. ■ If the standard handle is used, the handle side offset of both panels should be 3¹⁄₄" (8.25 cm) to all for finger clearance. ■ If an extended handle is used, the handle side offset of both panels should be 1.1 cm). Make sure the refrigerator location allows the doors with extended handles to open to 90 degrees. See "Door Swing Dimensions." ■ The dashed lines in the illustration represent the location and offsets of raised wood panel.