KitchenAid KVUB600DSS Installation Guide - Page 12

Range Hood Care

Get KitchenAid KVUB600DSS PDF manuals and user guides View all KitchenAid KVUB600DSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

RANGE HOOD CARE Cleaning IMPORTANT: Clean the hood and grease filters frequently according to the following instructions. Replace grease filters before operating hood. Exterior Surfaces: To avoid damage to the exterior surface, do not use steel wool or soap-filled scouring pads. Always wipe dry to avoid water marks. Cleaning Method: ■ Liquid detergent soap and water, or all-purpose cleanser Non-Vented (Recirculating) Installation Filters The charcoal filter is not washable. It should last up to 6 months with normal use. Replace with Charcoal Filter Kit Number W10272068. To Replace Charcoal Filter: 1. Cover the grille that covers the blower motor with the charcoal filter so that the slots on the filter correspond to the pins on the sides of the motor grille. ■ Wipe with damp soft cloth or nonabrasive sponge, then rinse with clean water and wipe dry. Metal Grease Filter: 1. Open the stainless steel panel. Grasp panel at the front corners and pull down to disengage the 2 catch pins from the spring catches. The panel is attached at the rear and will rotate down. D A B C A. Metal filters B. Stainless steel panel C. Catch pins (2) D. Spring catches (2) 2. Remove each filter by pulling the spring release handle and then pulling down the filter. AB C A. Charcoal filter B. Pins C. Blower motor 2. Turn the charcoal filter clockwise to lock it. 3. Repeat steps 1-2 on the other filter. Replacing a Led Lamp The LED lights are replaceable by a service technician only. See "Assistance and Service" section for service contact information. A A. Spring release handle 3. Wash metal filters as needed in dishwasher or hot detergent solution. 4. Reinstall the filter by making sure the spring release handles are toward the front. Insert aluminum filter into upper track. 5. Push in spring release handle. 6. Push up on metal filter and release handle to latch into place. 7. Repeat steps 1-5 for the other filter. 8. Close the stainless steel panel. Engage the (2) pins in the spring catches to secure. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
12
RANGE HOOD CARE
Cleaning
IMPORTANT:
Clean the hood and grease filters frequently
according to the following instructions. Replace grease filters
before operating hood.
Exterior Surfaces:
To avoid damage to the exterior surface, do not use steel wool or
soap-filled scouring pads.
Always wipe dry to avoid water marks.
Cleaning Method:
■
Liquid detergent soap and water, or all-purpose cleanser
■
Wipe with damp soft cloth or nonabrasive sponge, then rinse
with clean water and wipe dry.
Metal Grease Filter:
1.
Open the stainless steel panel. Grasp panel at the front
corners and pull down to disengage the 2 catch pins from the
spring catches. The panel is attached at the rear and will
rotate down.
2.
Remove each filter by pulling the spring release handle and
then pulling down the filter.
3.
Wash metal filters as needed in dishwasher or hot detergent
solution.
4.
Reinstall the filter by making sure the spring release handles
are toward the front. Insert aluminum filter into upper track.
5.
Push in spring release handle.
6.
Push up on metal filter and release handle to latch into place.
7.
Repeat steps 1-5 for the other filter.
8.
Close the stainless steel panel. Engage the (2) pins in the
spring catches to secure.
Non-Vented (Recirculating) Installation Filters
The charcoal filter is not washable. It should last up to 6 months
with normal use. Replace with Charcoal Filter Kit Number
W10272068.
To Replace Charcoal Filter:
1.
Cover the grille that covers the blower motor with the
charcoal filter so that the slots on the filter correspond to the
pins on the sides of the motor grille.
2.
Turn the charcoal filter clockwise to lock it.
3.
Repeat steps 1-2 on the other filter.
Replacing a Led Lamp
The LED lights are replaceable by a service technician only. See
“Assistance and Service” section for service contact information.
A. Metal filters
B. Stainless steel panel
C. Catch pins (2)
D. Spring catches (2)
A. Spring release handle
A
B
C
D
A
A. Charcoal filter
B. Pins
C. Blower motor
A
B
C