KitchenAid KXU2836JSS Dimension Guide - Page 2

Cabinet Dimensions, Product Dimensions, Location Requirements, Important, For Mobile Home

Page 2 highlights

PRODUCT DIMENSIONS 9 23.0 cm) 6" (15.2 cm) front edge to damper centerline 21" (53.3 cm) 6" (15.2 cm) 9 24.9 cm) 2³⁄₄" (7.0 cm) 30" (76.2 cm) - 30" (76.2 cm) model 36" (91.4 cm) - 36" (91.4 cm) model 11 28.1 cm) 1³⁄₄" (2.4 cm - 4.4 cm) trim extension 6⁷⁄₈" (17.5 cm) with screen extended CABINET DIMENSIONS 15" (38.1 cm) min. clearance upper cabinet to countertop 30" (76.2 cm) or 36" (91.4 cm) min. cabinet opening width 24" (61 cm) min. 32" (81 cm) suggested max. bottom of cabinet to cooking surface 12" (30.5 cm) cabinet depth 36" (91.4 cm) base cabinet height 15" (38.1 cm) min. upper cabinet height LOCATION REQUIREMENTS IMPORTANT: Observe all governing codes and ordinances. Have a qualified technician install the range hood. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located behind the filter on the left rear wall of the range hood. Range hood location should be away from strong draft areas, such as windows, doors, and strong heating vents. Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance. Consult your cooktop/range manufacturer installation instructions before making any cutouts. Grounded electrical outlet is required. See "Electrical Requirements" section. The range hood is factory set for vented installations through the roof or wall. For non-vented (recirculating) installations see "Non-Vented (recirculating) Installation Through the Soffit/Cabinet" in the "Prepare Location" section. Recirculation Kit Part Number W10356918 is available from your dealer or an authorized parts distributor. All openings in ceiling and wall where range hood will be installed must be sealed. For Mobile Home Installations The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local codes. Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation our products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice. Page 2 of 2 Ref. W10342488A 3/15/12

  • 1
  • 2

Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10342488A
3/15/12
Page 2 of 2
CABINET DIMENSIONS
PRODUCT DIMENSIONS
30"
(76.2 cm) - 30" (76.2 cm) model
36" (91.4 cm) - 36" (91.4 cm) model
6
⁷⁄₈
" (17.5 cm) with
screen extended
11
¹⁄₁₆
" (28.1 cm)
9
¹³⁄₁₆
" (24.9 cm)
¹⁵⁄₁₆
" - 1
³⁄₄
" (2.4 cm - 4.4 cm)
trim extension
2
³⁄₄
" (7.0 cm)
21" (53.3 cm)
6" (15.2 cm)
front edge to
damper centerline
6" (15.2 cm)
9¹⁄₁₆
" (23.0 cm)
LOCATION REQUIREMENTS
IMPORTANT:
Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the installer
s
responsibility to comply with installation clearances specified on the
model/serial rating plate. The model/serial rating plate is located behind
the filter on the left rear wall of the range hood.
Range hood location should be away from strong draft areas, such as
windows, doors, and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions provide minimum clearance. Consult your cooktop/range
manufacturer installation instructions before making any cutouts.
Grounded electrical outlet is required. See
Electrical Requirements
section.
The range hood is factory set for vented installations through the roof or
wall. For non-vented (recirculating) installations see
Non-Vented
(recirculating) Installation Through the Soffit/Cabinet
in the
Prepare
Location
section. Recirculation Kit Part Number W10356918 is available
from your dealer or an authorized parts distributor.
All openings in ceiling and wall where range hood will be installed must be
sealed.
For Mobile Home Installations
The installation of this range hood must conform to the Manufactured
Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the
Federal Standard for Mobile Home Construction and Safety, title 24, HUD,
Part 280) or when such standard is not applicable, the standard for
Manufactured Home Installation 1982 (Manufactured Home Sites,
Communities and Setups) ANSI A225.1/NFPA 501A*, or latest edition, or
with local codes.
15" (38.1 cm)
min. clearance
upper cabinet
to countertop
12" (30.5 cm)
cabinet depth
30" (76.2 cm) or
36" (91.4 cm) min.
cabinet opening width
24" (61 cm) min.
32" (81 cm)
suggested max.
bottom of cabinet
to cooking surface
36" (91.4 cm)
base cabinet
height
15" (38.1 cm)
min. upper
cabinet height