KitchenAid KXU8036YSS Dimension Guide - Page 1

KitchenAid KXU8036YSS Manual

Get KitchenAid KXU8036YSS PDF manuals and user guides View all KitchenAid KXU8036YSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

30" (76.2 cm) and 36" (91.4 cm) Retractable (Pop-Up) Downdraft Vent System PRODUCT MODEL NUMBERS PRODUCT DIMENSIONS KXD4630Y KXD4636Y KXD4736Y Electrical A 120 Volt, 60 Hz., AC only 15-amp fused, electrical circuit is required. LOCATION REQUIREMENTS NOTE: Downdraft vent is installed directly behind the cooktop. Install the downdraft vent first, then install the cooktop. IMPORTANT: Observe all governing codes and ordinances. q Have a qualified technician install the downdraft vent. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the front of the downdraft vent above the terminal box cover. q Downdraft vent location should be away from strong draft areas, such as windows, doors, and strong heating vents or fans. q Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance. q Consult the cooktop manufacturer installation instructions before making any cutouts. Check that the downdraft vent and cooktop location will clear the cabinet walls, backsplash, and rear wall studs inside the cabinet. Check for the minimum distance between the front edge of the countertop and the front edge of the cooktop. The minimum horizontal distance between the overhead cabinets is the same as the width of the installed downdraft vent. q All openings in ceiling and wall where the downdraft vent will be installed must be sealed. q Grounded electrical outlet is required. See "Electrical Requirements" section. q When installing the downdraft vent, the cabinet drawer will need to be removed and the drawer front installed permanently to the cabinet. Cabinet Construction: Downdraft vent is designed for use in a cabinet with a depth of 24" (61 cm). Some installations require a countertop deeper than 25" (63.5 cm). See the Countertop Cutout Dimensions section. The maximum depth of the overhead cabinet is 13" (33 cm). Overhead cabinets installed at either side of the downdraft vent must be 18" (45.7 cm) above the cooking surface. For Mobile Home Installations The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local codes. Models with interior-mounted blower motor Top trim widths: 30" (76.2 cm) 36" (91.4 cm) 13¹⁄₂" (34.3 cm) retractable vent height 27" (68.6 cm) for 30" (76.2 cm) vent 33" (83.8 cm) for 36" (91.4 cm) vent 1¹⁄₂" (3.8 cm 0.95 cm) 13¹⁄₈" (33.4 cm) 5¹⁄₄"(13.3 cm) for 30" (76.2 cm) vent 8¹⁄₄"(21.0 cm) for 36" (91.4 cm) vent 28¹⁄₂" (72.4 cm) ³⁄₄ (1.9 cm) 16¹⁄₂" (42.0 cm) 10" (25.4 cm) 2¹⁄₈" (5.4 cm) Models with exterior-mounted blower motor 4³⁄₄" (12.1 cm) 13¹⁄₈" (33.4 cm) 6 16.7 cm) 10" (25.4 cm) diameter vent collar 8¹⁄₄" (21.0 cm) 16¹⁄₂" (42.0 cm) ³⁄₄" (1.9 cm) CABINET DIMENSIONS Interior-mounted blower motor model 10" (25.4 cm) Exterior-mounted blower motor model A 12.7 mm) minimum ¹⁄₂" (12.7 mm) minimum 21 Cutouts are (54.1 cm) for 3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent system. 21 54.1 cm) Locate power supply junction box at lower left hand rear corner of the cabinet. NOTES: Centerline of cooktop cutout q See cooktop manufacturer's instructions for cooktop cutout depth and width. q Use dimensions for vent system cutout location that applies to your installation. q Interior mounted blower systems connect with 3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent system. The cutout locations for this vent system will depend on your specific installation. Locate power supply junction box at lower left hand rear corner of the cabinet. NOTES: q See cooktop manufacturer's instructions for cooktop cutout depth and width. q Exterior-mounted blower systems connect with 10" (25.4 cm) round vent. The cutout locations for this vent system will depend upon your specific installation. Page 1 of 3 Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation our products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice. Ref. W10342489D 1/31/2012

  • 1
  • 2
  • 3
30" (76.2 cm) and 36" (91.4 cm) Retractable (Pop-Up)
Downdraft Vent System
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10342489D
1/31/2012
Page 1 of 3
PRODUCT MODEL NUMBERS
PRODUCT DIMENSIONS
KXD4630Y
KXD4636Y
KXD4736Y
Electrical
A 120 Volt, 60 Hz., AC only 15-amp fused, electrical circuit is required.
Models with interior-mounted blower motor
Models with exterior-mounted blower motor
4³⁄₄
" (12.1 cm)
13
¹⁄₈
" (33.4 cm)
6
⁹⁄₁₆
"
(16.7 cm)
10" (25.4 cm)
diameter
vent collar
16
¹⁄₂
" (42.0 cm)
8
¹⁄₄
"
(21.0 cm)
³⁄₄
" (1.9 cm)
Top trim widths:
30" (76.2 cm)
36" (91.4 cm)
13¹⁄₂
" (34.3 cm)
retractable
vent height
27" (68.6 cm) for 30" (76.2 cm) vent
33" (83.8 cm) for 36" (91.4 cm) vent
16
¹⁄₂
" (42.0 cm)
10"
(25.4 cm)
2
¹⁄₈
" (5.4 cm)
28
¹⁄₂
"
(72.4 cm)
³⁄₈
" (0.95 cm)
1
¹⁄₂
" (3.8 cm)
13
¹⁄₈
" (33.4 cm)
5
¹⁄₄
"(13.3 cm)
for 30" (76.2 cm) vent
8
¹⁄₄
"(21.0 cm)
for 36" (91.4 cm) vent
³⁄₄
(1.9 cm)
LOCATION REQUIREMENTS
NOTE:
Downdraft vent is installed directly behind the cooktop. Install the
downdraft vent first, then install the cooktop.
IMPORTANT:
Observe all governing codes and ordinances.
●
Have a qualified technician install the downdraft vent. It is the installer’s
responsibility to comply with installation clearances specified on the
model/serial rating plate. The model/serial rating plate is located on the front of
the downdraft vent above the terminal box cover.
●
Downdraft vent location should be away from strong draft areas, such as
windows, doors, and strong heating vents or fans.
●
Cabinet opening dimensions that are shown must be used. Given dimensions
provide minimum clearance.
●
Consult the cooktop manufacturer installation instructions before making any
cutouts.
Check that the downdraft vent and cooktop location will clear the
cabinet walls, backsplash, and rear wall studs inside the cabinet.
Check for the minimum distance between the front edge of the
countertop and the front edge of the cooktop. The minimum horizontal
distance between the overhead cabinets is the same as the width of the
installed downdraft vent.
●
All openings in ceiling and wall where the downdraft vent will be installed must
be sealed.
●
Grounded electrical outlet is required. See “Electrical Requirements” section.
●
When installing the downdraft vent, the cabinet drawer will need to be removed
and the drawer front installed permanently to the cabinet.
Cabinet Construction:
Downdraft vent is designed for use in a cabinet with a depth of 24" (61 cm).
Some installations require a countertop deeper than 25" (63.5 cm). See the
Countertop Cutout Dimensions section.
The maximum depth of the overhead cabinet is 13" (33 cm). Overhead cabinets
installed at either side of the downdraft vent must be 18" (45.7 cm) above the
cooking surface.
For Mobile Home Installations
The installation of this range hood must conform to the Manufactured Home
Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal
Standard for Mobile Home Construction and Safety, title 24, HUD, Part 280) or
when such standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI
A225.1/NFPA 501A*, or latest edition, or with local codes.
l
e
d
o
m
r
o
t
o
m
r
e
w
o
l
b
d
e
t
n
u
o
m
-
r
o
i
r
e
t
x
E
l
e
d
o
m
r
o
t
o
m
r
e
w
o
l
b
d
e
t
n
u
o
m
-
r
o
i
r
e
t
n
I
A=
¹⁄₂
" (12.7 mm)
minimum
21
⁵
⁄₁₆
"
(54.1 cm)
Cutouts are
for 3
¹⁄₄
" x 10"
(8.3 x 25.4 cm)
rectangular or 6"
(15.2 cm) round
vent system.
Centerline of cooktop cutout
21
⁵
⁄₁₆
"
(54.1 cm)
Locate power
supply junction
box at lower
left hand
rear corner
of the cabinet.
10
" (25.4 cm)
¹⁄₂
" (12.7 mm)
minimum
Locate power
supply junction
box at lower
left hand
rear corner
of the cabinet.
CABINET DIMENSIONS
NOTES:
●
See cooktop manufacturer’s instructions for cooktop cutout depth and
width.
●
Use dimensions for vent system cutout location that applies to your
installation.
●
Interior mounted blower systems connect with 3
¹⁄₄
" x 10" (8.3 x 25.4 cm)
rectangular or 6" (15.2 cm) round vent system. The cutout locations for
this vent system will depend on your specific installation.
NOTES:
●
See cooktop manufacturer’s instructions for cooktop cutout depth and
width.
●
Exterior-mounted blower systems connect with 10" (25.4 cm) round vent.
The cutout locations for this vent system will depend upon your specific
installation.